REYEE RG-E5 Wireless Router User Manual

REYEE RG-E5 Wireless Router User Manual

Packing List

Appearance

Please connect the power and network cables as shown below.

Indicator

Network Connection

1. Connect to the SSID @Reyee-sXXXX, and the configuration page will be displayed automatically; if not, please visit 192.168.110.1.

2. The router will match the Internet access method. Please configure the network parameters accordingly.
3. Configure the SSID and password. After the configuration working, you can connect to the SSID and access to the Internet.

Access the internet by app:

1. Download the Reyee Router App

2. Register an account by one click

3. Tap Add Router and follow the guide for configuration

Scenario 2: Reyee Mesh

1. Place the second router within 2 meters of the first one, and power it on.
   After the system status indicator blinks in blue, wait for 2 to 3 minutes until it turns into steady blue. (If the router had been configured before, please press the Reset Button for more than 3 seconds to restore the factory settings)

2. Press the Reyee Mesh button on the first router.
   Press the Reyee Mesh button on the first router, and its indicator will blink in green during searching for routers. The indicator on the second router will also blink in green slowly during pairing. After 2 minutes, as the indicators on both routers turn into steady green, the pairing succeeds.

3. Place the second router to the specified position and power it on.
   After powering the router, wait for 3 to 5 minutes until the Reyee Mesh indicator turns into steady blue, it is all set and you can access the Internet. The meshed routers will share the same SSID and password. Visit 192.168.110.1 to check router connecting condition.
   If there is any network port available, you can connect cables as shown below. The wired connection is more stable

• Please note that Wi-Fi signal may be weak if two routers are placed far from each other or there are several obstacles like walls between them
• The Internet speed may be slow if there are multiple paired routers. We recommended mesh-up within 5 routers (1+4) to keep good performance

FAQs

1. What to do if I forget the management password?
   Try the Wi-Fi password which may be the same with the management password. If not, please restore the factory settings.

2. How to restore the factory settings?
   Power on the router and wait for 2 to 3 minutes until it starts up. Press the Reset button for more than 3 seconds until the system status indicator blinks. After the indicator changes to steady on and the SSID “@ Reyee-sXXXX” is broadcast, the router restores the factory settings successfully.

3. Can I connect multiple routers with network cables?
   Yes, and wired connection is more stable. You can connect the WAN port (yellow) from secondary device with the LAN port (black) from master router for wired connection.

Federal Communications Commission Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Statement:

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules

RF Exposure Warning!

This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

Caution!
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

IMPORTANT!
Operation in the band 5150-5250 MHz is only for indoor use.

Innovation, Science and Economic Development Canada Statement

This device complies with Industry Canada’s licenceϋexempt RSSs. Operation is subject to the following two conditions:

1. This device may not cause interference; and
2. This device must accept any interference, including interference that may cause undesired operation of the device

Exposure Statement:

The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSSϋ102 RF exposure, users can obtain Canadian information on RF exposure and compliance

RF Exposure Warning!

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body

5G UNII-1 Statement:

1. The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
2. For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;
3. For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>