AMERICAN EXPRESS MU8003 Premium Triple Monitor Stand Instruction Manual
- June 12, 2024
- American Express
Table of Contents
AMERICAN EXPRESS MU8003 Premium Triple Monitor Stand
Premium Triple Monitor Stand
Product Information:
Model | MA01N-36P-US1.0 |
---|---|
VESA Compatibility | 75x75mm, 100x100mm |
Monitor Size | 32″ |
Weight Capacity | (1~14kg)x3 (2.2~30.9lbs)x3 |
Product Usage Instructions
- Before assembly, check and ensure all necessary accessories are included and undamaged.
- Ensure proper installation by following the indicated instructions and cautions/attentions.
- Do not exceed the weight capacity specified. Keep small items included in the kit out of reach of children under 3 years old. Adult supervision is required.
- Choose between Clamp Installation or Grommet Base Installation:
Clamp Installation
- Mount Base (C) to Pole (B) using Bolts (O) and tighten with the 4mm Allen Key (R).
- Attach Bracket (E) to Base (C) with Bolts (N) and tighten with the 4mm Allen Key (R). Apply pads (P) to the bottom of Base (C) to avoid desk scratches.
- Attach Clamp (F) to Bracket (E) with Bolts (N) and adjust the Clamp width to fit with the desk.
- Tighten Clamp (F) to secure the stand to the desktop.
- Attach Base Support Cover (G) to Bracket (E).
Grommet Base Installation
- Mount Base (C) to Pole (B) using Bolts (O) and tighten with the 4mm Allen Key (R). Apply pads (P) to the bottom of Base (C) to avoid desk scratches.
- Place Carriage Bolt (H) through the center of Grommet Base (J) and mount it to the bottom of Base (C) using Bolts (N). Tighten with the 4mm Allen Key (R).
- Run Carriage Bolt (H) through the grommet hole on the desktop and attach Support Plate (I) and Wingnut (K). Tighten Wingnut (K) to secure the stand.
Arm Installation
- Install the Middle Head (Q), wire clip (M), and swivel arm (A) to the Pole (B). Fasten the bolt with the supplied 6mm Allen Key (T).
WARNING: For your safety, do not move the standoff your desk!
If you have any questions, please feel free to contact us via Amazon
WARNING!
If you have any confusion or are not quite sure about the installation, please
do not hesitate to ask for our help.
Before assembly, please check and make sure all necessary accessories are
included and undamaged. Improper installation (including not properly
following the indicated instructions or cautions /attentions), such as using
the product for monitors over its load capacity or for any purpose not
explicitly specied, may cause damage or serious injury. We would not be liable
for any damage or injury caused by improper mounting or inappropriate use.
The kit contains small items that could be choking hazards if swallowed.
Please keep them OUT OF REACH OF CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION
IS REQUIRED.
PACKAGE CONTENTS
DO NOT EXCEED WEIGHT CAPACITY
ASSEMBLY STEPS
STEP 1 : Clamp Installation OR Grommet Base Installation
Firstly mount Bace (C) to Pole (B) using Bolts (O). Tighten them using 4mm Allen Key (R).
OPTION A: Clamp Installation
Mount Bracket (E) to Base (C) with Bolts (N). Bolts could be tightened by the 4mm Allen Key (R).Apply pads (P) to the bottom of Base (C) to avoid desk scratches.
Attach Clamp (F) to Bracket (E) with Bolts (N) and 4mm Allen Key (R). Adjust the Clamp width to with desk.
STEP 1 : (Continued)
Secure stand to desktop by tightening Clamp (F) or by Allen key (T).
Attach Base Support Cover (E) to Bracket (E).
OPTION B: Grommet Base Installation
Place Carriage Bolt (H) through the center of Grommet Base (J).
Mount Grommet Base to Base (C) bottom with Bolts (N) and tighten them by 4mm
Allen Key (R).
Apply pads (P) to the bottom of Base (C) to avoid desk scratches.
Run Carriage Bolt (H) through grommet hole on desktop. Attach Support Plate (I) and Wingnut (K). At last, tighten Wingnut (K).
STEP 2 : Arm Installation
Install the middle head (Q) wire clip(M) and swivel arm (A) to the pole (B).
Fasten the bolt with supplied 6mm Allen key (T)
WARNING:
For your safety, do not move the stand oFF your desk!
STEP 3 : Attach Monitor
OPTION A: Flat Back Monitor
Attach the VESA plate (D) to the back of monitor and secure it by using a 6 mm
Allen Key (T) to tighten screws (M-A or M-C) along with washers (M-E).
Do not tighten the screws excessively or your monitor might be damaged.
OPTION B: Curved / Recessed Back Monitor
Attach the VESA plate (D) to the back of monitor and secure it by using a 6 mm
Allen Key (T) to tighten screws (M-B or M-D) along with washers (M-E) and
spacers (M-F).
Do not tighten the screws excessively or your monitor might be damaged.
STEP 4 : Hang Monitor
Slide the monitors onto the head of swivel arm. Install the security bolt (L). Make sure the security bolt is tightened before you rotate the monitor.
Guideline to adjust monitor tilting angle.
STEP 5 : Adjust Gas Spring Tension
For intended functioning of the mount, you will need to adjust the tension of Arm (A) in accordance with your monitor weight by 6mm Allen Key (T).
Situation 1: Arm falls down
Upper Arm with monitor falls down and fails to stay where intended.
Solution:
Turn the inside screw counterclockwise(“+”direction) to increase gas spring
tension until the arm can stay as intended.
Situation 2: Arm rises up/can’t be pressed down
Upper Arm with monitor rises up automatically or can’t be pressed down and
fails to stay where intended.
Solution:
Turn the inside screw clockwise(“-”direction) to decrease gas spring tension
until the arm can stay as intended.
Note2:
For how many circles the screw should be turned, please refer to the table
below.
Monitor Weight| 2.2 lbs
(1 kg)
| 6.6 lbs
(3 kg)
| 8.8 lbs
(4 kg)
| 15.4 lbs
(7 kg)
| 22 lbs
(10 kg)
| 28.7 lbs
(13 kg)
| 30.9 lbs
(14 kg)
---|---|---|---|---|---|---|---
Circles (AT LEAST)| min| 5| 7| 10| 13|
16| 20
STEP 6 : Cable Management
Remove Cable Cover
Remove bottom plastic covers from arm as shown in diagram.
Do not need to take much effort to pull the ends of the cable cover away from
the arm.
Attach Cable Cover
Run cables from monitor through bottom of arm. Reattach plastic covers as
shown in diagram.
Adjust as Desired
Adjust monitor position and rotation.
Store Allen keys (R, S) in wire clip (G) for future use.
Note: To ensure stability, the tightness of the rotating axis has been
preseted, so it would be kind of difficult to rotate the VESA plate.
Suggestion: Please attach the monitor first, then hold the two sides of it
with both hands, and rotate vigorously. If that doesn’t work out, please do
not hesitate to ask for our help.
Product Dimensions
CAUTION AND MAINTENANCE
- Don’t allow children to climb, stand, hang, or play on any part of monitor or stand.
- This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
- Check that the bracket is secure and safe to use at regular intervals (at least every three months).
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>