saferhome Wireless Alarm System User Manual
- June 7, 2024
- saferhome
Table of Contents
Wireless Alarm System
User Manual
Note:
1. The alarm system has been programmed already, please operate the system
according to part 2 of the manual;
2. If you want to add additional HTZSAFE sensors to the system, please
operate the system according to part 3 of the manual or contact us directly.
After-sale Service:
E-mail: contact@saferhomee.com
System Components And Usage
Plug-in Alarm Receiver
Power Plug: plug the receiver into a socket
Volume: 4 volume levels adjustable
Melody: 35 classic melodies optional
Indicator Light: flash for several seconds when the sensor be activated
Speaker: sound for several seconds when the sensor be activated
Solar Wireless Motion Sensor
Sensor Eye: detect the objects
Solar Panel: charge the built-in battery of the sensor
Drain Hole: used to drain out the rainwater (please note the drain hole
must be at the bottom when you install the sensor)
Charge
Jack: used to connect the additional solar panel or DC 5V power adapter
ON/OFF: turn on/off the sensor
ATTENTION PLEASE
The KIT includes a charging cable that is used to charge the solar wireless
motion sensor before use or if long-term continuously rainy days caused low
battery. Please charge the sensor for 4 hours as below:
Operation Instructions
Step 1
Plug the receiver into an outlet
The indicator
light of the receiver will flash for 15 seconds means working properly
Step 2 Turn on the Wireless Motion Sensor: Press the ON/OFF button 4
times
(OprNes/sO4FFtimes) (bleep prompt means work normally)
Step 3
Activate The Wireless Motion Sensor (wait about 30 seconds after you turned
on the sensor)
1st method: press the ON/OFF button twice
(the light of
the ON/OFF button will flash once means the motion sensor was activated and
sent the alarm signal)
2nd method: Ensure the sensor is turned away from you. and walkthrough in
front of the sensor to activate
(the light of
the ON/OFF button will flash once means the motion sensor was activated and
sent the alarm signal;and then the motion sensor will back to work mode
automatically after about 10 seconds if not detecting any movements)
Step 4
Press “Melody” once to choose the melody for this sensor, total 35 melodies
optional.
Step 5
Same steps for the other sensors
Step 6
Installations
Wireless Motion Sensor
Installation Notes:
-
Please fix the motion sensor tightly to ensure the position and the direction will not be moved easily by wind.
-
Please point the sensor towards an open field(not towards the trees or bushes)
-
please adjust the sensor a little down(not upward)
Other Settings
(1) How to add additional sensors to the receiver
(up to 32 sensors can be added to 1 receiver)
Step 1
Plug the receiver into an outlet
Step 2
Press and hold the “Volume” button for 5 seconds and release the button when
you heard a beep prompt and the indicator light flashing;
Step 3
Activate the sensor.
Note: please make the sensor close to the alarm receiver
(the indicator
light flashing 3 times means the sensor was activated properly)
(a ring tone prompt and the indicator light flashing quickly means the sensor
has been added to the wireless alarm receiver successfully)
Step 4
Activate the sensor again to confirm the sensor has been added to the receiver
already.
Step 5
Press the “Melody” button to choose the melody for this sensor. total 35
melodies optional.
(2) How to delete the sensors of the receiver
Step 1
Plug the receiver into a outlet
Step 2
Press and hold both the “Volume” button and “Melody” button for 10 seconds and
release the buttons when you heard a long beep prompt;
Note: all the sensors will be deleted by this operation.
(3) How to adjust the alarm volume
Step 1
Plug the receiver into an outlet
Step 2
Press the “Volume” once to adjust the volume of the receiver. (total 4 volume
levels adjustable)
(4) How to
change the melody for the sensors (total 35 melodies optional, match different
melody with different sensor)
Step 1
Plug the receiver into an outlet
Step 2
Activate the sensor first, and then press the “Melody” button to choose the
melody for this sensor Same steps for other sensors which have been added to
the receiver already.
(5) How to adjust the sensitivity of the sensor
The sensor has 3 sensitivities adjustable (High, Middle, Low)
Step 1
turn off the sensor by press the ON/OFF button 3 times
Step 2
If select Low sensitivity—turn on the sensor by pressing the ON/OFF button 3
times
If select Middle sensitivity—turn on the sensor by pressing the ON/OFF button
4 times
If select High sensitivity—turn on the sensor by pressing the ON/OFF button 5
times
Technical Parameters
Plug-in Alarm Receiver
Technical parameters
| Item | Technical Parameters |
|---|---|
| Working Voltage | AC 110V-220V |
| Working Current | Static Current 20mA; Alarming Current 300mA |
| Wireless Frequency | 433MHz FSK+FHSS |
Wireless Motion Sensor
Technical parameters
| Item | Technical Parameters |
|---|---|
| Detection Range | 50 feet(15m) |
| Detection Angle | 15 |
| Wireless Transmission Range | 1/4 Mile(400m) |
| Wireless Frequency | 433MHz FSK+FHSS |
| Working Voltage | 3.3V |
| Battery Type | Chargeable LiFePO4 Battery |
| Battery Capacity | 500mAh |
| Working Current | Static: 1mA; Alarming:60mA |
| Solar Panel Output Current | ≥100mA in Sunny days |
| Working Temperature Range | -22°F to 158°F(-30℃ to 70℃) |
After-sale Service:
E-mail:contact@saferhomee.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>