AMERICAN EXPRESS MU1006 Vertical Dual Monitor Stand Installation Guide

June 12, 2024
American Express

AMERICAN EXPRESS logo MU1006 Vertical Dual Monitor Stand
Installation Guide AMERICAN EXPRESS MU1006 Vertical Dual Monitor
Stand

INSTALLATION INSTRUCTION AMERICAN EXPRESS MU1006 Vertical Dual
Monitor Stand - icon 1(ZDT10-C02-US1)

If you have any questions, please feel free to contact us via Amazon.

Safety Caution

BEFORE ASSEMBLY

  • Layout all components and hardware. Check all parts are included and undamaged.
  • Should anybody intends to install or use this monitor stand, please read and understand this manual carefully.
  • If you do not understand these instructions or have any doubt about the safety instructions,
    assembly or use of this product, please contact our customer service.

WARNING

  • This product contains small items that could be a choking hazard if swallowed.
  • KEEP AWAY FROM CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.
  • Improper installation, such as using the product for monitors over its load capacity or for any purpose not explicitly specified, may cause damage or serious injury. We would not be liable for any damage or injury caused by improper mounting or inappropriate use.

CAUTION AND MAINTENANCE

  • Never allow children to climb, stand, hang, or play on any part of monitor or stand.
  • This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
  • Check that the bracket is secure and safe to use at regular intervals (at least every three months).

Installation Tools (Not Included)

AMERICAN EXPRESS MU1006 Vertical Dual Monitor Stand -
Tools

Supplied Parts and Hardware

AMERICAN EXPRESS MU1006 Vertical Dual Monitor Stand - Supplied
PartsHardware (Product)

AMERICAN EXPRESS MU1006 Vertical Dual Monitor Stand -
Hardware Hardware (Monitor)

AMERICAN EXPRESS MU1006 Vertical Dual Monitor Stand - Hardware
1NOTE: Not all hardware included will be used.

Product Dimensions

AMERICAN EXPRESS MU1006 Vertical Dual Monitor Stand - Product
Dimensions

STEP 1: Attach the Plate Component to Monitor

1-1 Select Monitor Screw Length
Thread screws by hand into the threaded holes on the back of your monitor after selecting which screw diameter fits your monitor. AMERICAN EXPRESS
MU1006 Vertical Dual Monitor Stand - Attach the Plate1-2 Select Monitor Screw Length
** When attaching plate to the flat screen, be careful not to over tighten screws and be sure that screws do not bottom out in the mounting holes. AMERICAN EXPRESS MU1006 Vertical Dual Monitor Stand - Monitor
Screw**

1-3 Attach the Plate Component
(a) For Flat Back AMERICAN EXPRESS MU1006 Vertical Dual Monitor Stand -
Plate Component(b) For Round Back / Extra Space

AMERICAN EXPRESS MU1006 Vertical Dual Monitor Stand - Plate Component
1STEP 2: Support Pillar Installation
Connect two Support Pillars (3 & 3 ). Then insert 6pcs Screws (H) through the holes of Support Pillars ( 3 &4 ), and use the 4mm Allen Key (G) to tighten.
AMERICAN EXPRESS MU1006 Vertical Dual Monitor Stand - Support
Pillar
Put Base 1 on the table; put Washers (B) and Bolts (A) on the base; keep clip holes of Support Pillar 4 toward backside then put Plastic Cover (D) and Support Pillar 4 under the base. Then tighten the bolts (A) with the 4mm allen key (G).
AMERICAN EXPRESS MU1006 Vertical Dual Monitor Stand - Support Pillar
1STEP 3: Apply Foot Pads to the Base
Hold the Support Pillar 4 with one hand and tear off plastic film of Foot Pads (F), then attach Foot Pads (F) near four conors of the Base 1 bottom.
AMERICAN EXPRESS MU1006 Vertical Dual Monitor Stand - Support Pillar
2STEP 4: Attach Monitor with Plate Component to Pillar
Turn over the base. Choose the appropriate position for your monitors, hang the monitors onto the Support Pillar, then tighten them with Handle Bolts (C). AMERICAN EXPRESS MU1006 Vertical Dual Monitor Stand - Support Pillar
3

STEP 5: Cable Management
Attach Wire Clips (E) into the holes of Support Pillar. Manage cables with the Wire  Clips (E). AMERICAN EXPRESS MU1006 Vertical Dual Monitor Stand -
Support Pillar 4

STEP 6: Adjustments (If necessary)
Tilt Adjustment

  1. Slightly loosen tilting bolt with the Allen Key(G).
  2. Hold the monitor with both hands and adjust monitor to your desired tilt angle.
  3. Retighten tilting bolt to secure the monitor in place.

AMERICAN EXPRESS MU1006 Vertical Dual Monitor Stand - Support Pillar
5Note:
When tilted, if the monitor sags or does not stay, and if the above method is useless, please feel free to contact our customer service.
STEP 6: Adjustments (If necessary)
Rotation Adjustment AMERICAN EXPRESS MU1006 Vertical Dual Monitor
Stand - Support Pillar 6Swivel Adjustment
AMERICAN EXPRESS MU1006 Vertical Dual Monitor Stand - Support Pillar
7

Documents / Resources

| AMERICAN EXPRESS MU1006 Vertical Dual Monitor Stand [pdf] Installation Guide
YD5010 DWD701 -US1, MU1006, MU1006 Vertical Dual Monitor Stand, Vertical Dual Monitor Stand, Dual Monitor Stand, Monitor Stand, Stand
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

American Express User Manuals

Related Manuals