American Express MU7005 Premium Single Monitor Stand Instruction Manual

June 12, 2024
American Express

American Express MU7005 Premium Single Monitor Stand Instruction Manual
American Express MU7005 Premium Single Monitor Stand

SAFETY INSTRUCTIONS

BEFORE ASSEMBLY

  • Layout all components and hardware. Check all parts are included and undamaged.
  • Should anybody intends to install or use this monitor arm, please read and understand this manual carefully

WARNING

  • This product contains small items that could be a choking hazard if swallowed.
  • KEEP AWAY FROM CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.
  • Improper installation, such as using the product for monitors over its load capacity or for any purpose not explicitly specified, may cause damage or serious injury. We would not be liable for any damage or injury caused by improper mounting or inappropriate use.
  • If you do not understand these instructions or have any doubt about the safety instructions, assembly or use of this product, please contact our customer service.

PACKAGE CONTENTS

  • 5 (×1) Base

  • 6 (×1) Lower arm

  • 7 (×1) Upper arm

  • 8 (×1) Bracket

  • 9 (×1) VESA plate

  • 10 (×1) Clamp

  • 11 (×1) Long Bolt

  • 12 (×1) Washer

  • 13 (×1) Cushion

  • 1 (×4) Screw M4×25

  • 2 (×4)Screw M5×25|

  • 3 (×4)Washer

  • 4 (×4)Spacer H15mm

  • A (×4) Screw M4x10

  • B (×4) Screw M5x10

  • C (×3) bolt M6×12

  • D (×4) bolt M6×10

  • E (×1) M5×20

  • F(×1)4mm Allen Key

  • G (×1)5mm Allen Key

  • H(×1)6mm Allen Key

DO NOT EXCEED WEIGHT CAPACITY.

Clamp Installation OR Grommet Base Installation

OPTION A: Clamp Installation
Mount Bracket (8) to Base (5) with Bolts (C). Bolts could be tightened by the 4mm Allen Key (F). Install the cushion (13) on the base (5) to avoid scratching the table top.
Clamp Installation

There are two sets of key slot holes to choose from for different desktop thicknesses. Attach Clamp (10) to Bracket (8) with Bolts (D) then tighten them with 4mm Allen key (F).

For Desks 0.39” to 2.56” use the top four holes
Clamp Installation

For Desks 1.18” to 3.15” use the bottom four holes
Clamp Installation

Adjust the Clamp width to fit with desk.
Secure stand to desktop by tightening Clamp or by Allen key (G).
Clamp Installation

Continued

OPTION B: Grommet Base Installation

Ensure the desktop has a hole between 0.4” and 2.4” in diameter to use this option. Using a grommet hole that is already in your desktop is acceptable.
Grommet Base Installation

Install the cushion (13) on the base (5) to avoid scratching the table top.
Grommet Base Installation

Insert the long bolt (11) through the washer (12) and the hole on the table top, and then use the Allen key (H) to tighten
Grommet Base Installation

Arm Installation

Connect the upper arm (7) and the lower arm (6) with the screw (E) through the rivet nut, and tighten it with an Allen key (F).
Arm Installation

WARNING:

  1. Tighten the screws (E) on the Lower Arm and this will prevent the Upper Arm from becoming separated from the Lower Arm during adjustment.
  2. Please don’t use any drills it will damage the screw.

Insert the lower arm into the base and adjust the screw with the Allen key (F) to fix the lower arm.
Arm Installation

  1. The Top Screw
    OPTION A : If you want to swivel ±180°, just loosen the top screw.
    OPTION B : If you want to swivel ±90°, just lock the top screw.

  2. The Lower Screw
    The lower screw are used to adjust the tightness of the connection between the base and the bracket arm to avoid the arms from shaking.

The screws on the top are used to limit the position.

Attach Monitor

OPTION A: Flat Back Monitor
Attach Monitor

Attach the VESA plate (9) to the back of monitor and secure it by using a 5mm Allen Key (G) to tighten screws (A or B) along with washers (3).
Attach Monitor

Do not tighten the screws excessively or your monitor might be damaged.

OPTION B: Curved / Recessed Back Monitor
Attach Monitor

Attach the VESA plate (9) to the back of monitor and secure it by using a 5mm Allen Key (G) to tighten screws (1 or 2) along with washers (3) and spacers (4).

Do not tighten the screws excessively or your monitor might be damaged.
Attach Monitor

Hang Monitor

Slide the monitors onto the head of arm.
Lock the security knob. Make sure the security knob is locked before you rotate the monitor.

When the display is inserted into the quick release head, make sure the knob is vertical
Hang Monitor

After insertion, rotate the knob 90 degrees to the left.
Hang Monitor

Important Notice:
The pressure of the gas spring is initially set to an intermediate value. So when the monitor hangs, make sure to hold it with both hands and don’t let it drop suddenly.

Adjust monitor tilting angle

Adjust monitor tilting angle

Turn clockwise to tighten
Turn counterclockwise to loose

Limit screw can prevent the head from sinking. This screw can be removed when you need the display to be lowered (0°~-45°).
Adjust monitor tilting angle

Before removing the screw +90°~0°
Adjust monitor tilting angle

After removing the screw +90°~-45°
Adjust monitor tilting angle

Adjust Gas Spring Tension

For proper functioning of this mount, depending on different weight of monitor you might need to adjust tension in upper arm (7) using 6mm Allen Key (H).
Adjust Gas Spring Tension

The initial value of the scale is the middle value of the force range. The force value of the gas spring can be understood through the scale, which is convenient for modification

Note:
Be sure to keep the arm in horizontal position during adjustment. Or else it would be dicult to adjust the mount or damage the mount.


Situation 1: Arm falls down

Upper Arm with monitor falls down and fails to stay where intended.

Solution:
Turn the inside screw counterclockwise (“+”direction) to increase gas spring tension until the arm can stay as intended.


Situation 2: Arm rises up / can’t be pressed down

Upper Arm with monitor rises up automatically or can’t be pressed down and fails to stay where intended.

Solution:
Turn the inside screw clockwise (“-”direction) to decrease gas spring tension until the arm can stay as intended.
Adjust Gas Spring Tension
Adjust Gas Spring Tension

Cable Management

Remove Cable Cover
Remove the cable cover by grasping both sides of one end of the cover with the fingers of both hands, and then pulling it to the left and right respectively.
Remove Cable Cover

Attach Cable Cover
Run cables from monitor through bottom of arm. Reattach plastic covers as shown in diagram.
Attach Cable Cover 

Adjust as Desired

Adjust as Desired

Adjust monitor position and rotation.

Tilt
Swivel
Rotation
Height

Note: To ensure stability, the tightness of the rotating axis has been preseted, so it would be kind of dificult to rotate the VESA plate.

Suggestion: Please attach the monitor first, then hold the two sides of it with both hands, and rotate vigorously. If that doesn’t work out, please do not hesitate to ask for our help
Adjust as Desired

WARNING:
For your safety, do not move the stand off your desk!
Adjust as Desired

Product Dimensions

Product Dimensions

CAUTION AND MAINTENANCE:

  • Never allow children to climb, stand, hang, or play on any part of monitor or stand.
  • This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
  • Check that the bracket is secure and safe to use at regular intervals (at least every three months)

American Express Logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

American Express User Manuals

Related Manuals