dji Dock 2 Charging Base Instruction Manual
- June 1, 2024
- DJi
Table of Contents
dji Dock 2 Charging Base
INSTRUCTION MANUAL
WE ARE HERE FOR YOU
https://enterprise.dji.com/dock-2/downloads
This content is subject to change without prior notice.
DJI and MATRICE are trademarks of DJI.
Copyright © 2023 DJI All Rights Reserved.
OVERVIEW
1. Status LED
2. Power Port
3. Battery Port
Disclaimer
Carefully read this entire document and all safety and compliance guidelines provided before use.
Warnings
1. Keep liquids away from the inside of the charging base.
2. The charging base is only compatible with DJI Matrice 3D Series
Intelligent Flight Battery. DO NOT attempt to use the charging base with other
battery models.
3. Place the charging base on a flat and stable surface when in use. Make
sure the device is properly insulated to prevent fire hazards.
4. DO NOT attempt to touch the metal terminals on the ports.
5. Clean the metal terminals with a clean, dry cloth if there is any
noticeable buildup.
Introduction
The DJI Matrice 3D Series Charging base is compatible with the DJI USB-C Power Adapter (100W). The charging base can be used to charge DJI Matrice 3D Series Intelligent Flight Battery when the battery is not installed in the aircraft.
Usage
1. Insert the Intelligent Flight Battery into the battery port. Connect the
charging base to a power outlet (100-240 VAC, 50-60 Hz) using the DJI USB-C
Power Adapter (100W).
2. Refer to the Status LED Descriptions for more information about the
blinking patterns of the status LED.
3. Disconnect the Intelligent Flight Battery from the charging base when
charging is complete.
Status LED
| Blinking Pattern | Description |
|---|---|
| Solid yellow | The battery is not inserted |
| Pulses green | Charging the battery |
| Solid green | The battery is fully charged |
| Blinks yellow | Temperature of the battery or the charging base is too low or |
too high (wait until the battery and the charging base cools down, no further
operation needed)
Solid Red| Power supply or battery error (remove and reinsert the battery or
unplug and plug in the adapter)
Specifications
| Product Model | CHX220-100 |
|---|---|
| Compatible Battery Model | BPX220-7811-14.76 |
| Weight | Approx. 85 g |
| Input | 5-20 V, 5 A |
| Operating Temperature | 5° to 40° C (41° to 104° F) |
| Charging Time | DJI USB-C Power Adapter (100W): Approx. 1 hour 10 minutes |
Compliance Statement
FCC Compliance Statement
Supplier’s Declaration of Conformity
Product name: CHARGING BASE
Model Number: CHX220-100
Responsible Party: DJI Research LLC
Responsible Party Address: 17301 Edwards Road, Cerritos, CA 90703
Website: www.dji.com
We, DJI Research LLC, being the responsible party, declares that the above
mentioned model was
tested to demonstrate complying with all applicable FCC rules and regulations.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two
conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any
interference received, including interference that may cause undesired
operation.
Any changes or modifications not expressly approved by the party responsible
for compliance
could void the user’s authority to operate the equipment.
ISED Compliance
CAN ICES-003 (B) / NMB-003(B)
EU & UK Compliance Notice
EU Compliance Statement : SZ DJI TECHNOLOGY CO., LTD. hereby declares
that this device
(CHARGING BASE) is in compliance with the essential requirements and other
relevant provisions of the Directive 2014/30/EU.
A copy of the EU Declaration of Conformity is available online at www.dji.com
/euro-compliance
EU contact address: DJI GmbH, Industriestrasse 12, 97618, Niederlauer, Germany
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>