sistema AVALON200ZOOM 200W Outdoor LED Gobo Porjector with Zoom User Manual

: June 12, 2024
: Sistema

Table of Contents

sistema AVALON200ZOOM 200W Outdoor LED Gobo Porjector with Zoom
Operate Introduction
DMX Channel
RDM Supported Parameters
Read User Manual Online (PDF format)
Download This Manual (PDF format)

sistema AVALON200ZOOM 200W Outdoor LED Gobo Porjector with Zoom

AVALON200 ZOOM 200W outdoor LED Gobo Projector with zoom

Operate Introduction 4 MODES

DMX mode
Auto run mode
Master/Slave
Manual mode

DMX Channels: 12 Channels

Functions: Dimming, color wheel, rotating gobo wheel, focus, zoom, prism

4 menu buttons: Long press MODE+SET for 3 seconds to unlock,press MODE+SET in other interface to quickly lock

Menu

DMX Address
Auto Mode
Slave Mode
Manual Control
Settings
Calibrations
Information

Functions DMX Address code setting

Auto run mode:

Dimming: 0-255
Strobe: 0-255
Color: 0-255
ColorF: 0-255
Gobo: 0-255
Gobo_R: 0-255
Gobo_F: 0-255
Focus: 0-255
Zoom: 0-255
Prism: 0-255

Settings:

Curve Select
DMX Fail
Display
Language
Key Lock
Back Light
Reset
Default Password

Information (version and UID code)

Color: 000-255
Gobo: 000-255
Gobo_R: 000-255
Focus: 000-255
Zoom: 000-255
Prism: 000-255
Recover Calibration

Menu Description:

DMX Address:

Press the UP/DOWN button to set the initial address code (001 ~ 512). After setting the address code, press the SET button to confirm the save and automatically exit to return to the main menu. The fixture is in DMX mode after this operation.

Auto Mode: Select the Auto Mode menu, there are two menus for option, one is Auto Mode, another is Scene Edit with 8 scenes for editing. Each\ scene can be edited independently, and also includes all the DMX channels function and time-keeping function, but no Reset function. The editing process is the same as Manual Control, exit to save. This fixture has a maximum of 8 gobos, so it can set 8 scenes. If you need less than 8 scenes, set the scene time-keeping to 0. The
unit of time is seconds.

Slave Mode:

Select the Slave Mode menu, press the SET button to enter Slave Mode, then it will receive the signal from the master and keep the same state as the master. The fixture in Auto Mode or Manual mode is the master. In the screensaver, it will switch to DMX mode in
response to the channel sent from the console whenever the master or slave receives the DMX512 signal.

DMX Fail:

OFF (No DMX, lighting is off.), HOLD (No DMX, lighting keeps the original state).

Display:

The display reverse is used when the fixture is upside down.

Language:

English or Chinese

Key Lock:

When using the key lock function, no key operation after 30 seconds, the key is locked. Pressing the key in the locked state is invalid. It needs to press the MODE+SET key combination for 3 seconds to unlock.

Back Light:

Select always on or 60S off if no operation

Reset:

In order to verify whether the motor is working normally, and whether to save

Operate Introduction

4 MODES：DMX mode, Auto run mode, Master/Slave, Manual mode

DMX Channels：12 Channels
Function：Dimming, color wheel, rotating gobo wheel, focus, zoom, prism 4 menu buttons：（Long press MODE+SET for 3 seconds to unlock, press MODE+SET in other interface to quickly lock）

MODE| Menu/Back to previous

menu

---|---
SETUP| Confirm the selection

function

UP| Select the previous option
DOWN| Select the next option

Menu

Menu 1	Menu 2	Menu 3	Functions
1.DMX Address	001 – 512		DMX Address code

setting

2.Auto Mode| Auto Run| | Auto run mode
Scene Edit| Scene1-Scene8| 1. Dimming:0-255
| | | 2. Strobe:0-255
| | | 3. Color:0-255
| | | 4. Color_F:0-255
| | | 5.Gobo:0-255
| | | 6. GoboR:0-255
| | | 7. Gobo_F:0-255
| | | 8. Focus:0-255
| | | 9. Zoom:0-255
| | | 10. Prism:0-255
| | | 11. Prism R:0-255
| | | 12.Time:0-255
3.Slave mode| | |
4.Manual Control| 1.Dimmer:    0-255| |
2.Strobe:       0-255|
3.Color:        0-255|
4.ColorF:      0-255|
5.Gobo:        0-255|
6.Gobo_R:    0-255|
7.Gobo_F:     0-255|
8.Focus:        0-255|
9.Zoom:        0-255|
10.Prism:      0-255|
| 11.PrismR:    0-255| |
---|---|---|---
5.Settings| 1.Curve Select| 1.Linear|
2.Square Law|
3.InvSquareLaw|
4.S-Curve|
2.DMX Fail| Off|
Hold|
3.Display| Normal|
Inverted|
4.Language| English|
Chinese|
5.Key Lock| Lock after 30s|
Unlocked|
6.Back Light| Off after 60s|
Always On|
7.Reset| No|
Yes|
8.Default| No|
Yes|
6.Calibrations| Password| 1.Color:000-255|
2.Gobo:000-255|
3.GoboR:000-255|
4.Focus:000-255|
5.Zoom:000-255|
6.Prism:000-255|
7. Recover

Calibration

|
7.Information| Information (version

and UID code)

| |

Menu description:

DMX Address
Press the UP/DOWN button to set the initial address code (001 ~ 512). After setting the address code, press the SET button to confirm the save and automatically exit to return to the main menu. The fixture is in DMX mode after this operation.
Auto Mode
Select the Auto Mode menu, there are two menus for option, one is Auto Mode, another is Scene Edit with 8 scenes for editing. Each scene can be edited independently and also includes all the DMX channels function and time-keeping function, but no Reset function. The editing process is the same as Manual Control, exit to save.
This fixture has a maximum of 8 gobos, so it can set 8 scenes. If you need less than 8 scenes, set the scene time-keeping to “0”. The unit of time is seconds.
Slave Mode
Select the Slave Mode menu, press the SET button to enter Slave Mode, then it will receive the signal from the master and keep the same state as the master.
The fixture in Auto Mode or Manual mode is the master.
In the screensaver, it will switch to DMX mode in response to the channel sent from the console whenever the master or slave receives the DMX512 signal.
Manual Control
Select the Manual Control menu, Press the UP/DOWN button to select which function to operate. The right number after pressing the SET button is selected. Then press the UP/DOWN button to modify the value, long press to continuously modify, and press the SET button to change the options on the left. Press the MODE button to exit and return to the main menu. It will not exit the manual mode in this state. It’s need to enter other modes for switching. For example, if you set the DMX address, then will enter the DMX mode.
Settings
Curve Select
To choose one of linear dimming/square curve dimming/inverse square curve dimming/S-curve dimming. The characteristic of linear dimming is that the light output brightness maintains a linear relationship with the channel value; square curve dimming is relatively linear dimming, and the channel value range occupied in the low brightness area is more, that is the low brightness area is more abundantly adjusted; the low brightness area occupies few channels. When the channel value increases from 0 to up, the brightness quickly becomes very bright, and it allocates more channel value ranges in the high brightness area; the S-shaped curve is in the low brightness area Both the high-brightness area and the high-brightness area are allocated, and the medium-brightness area is few.
DMX Fail
“OFF” (No DMX, lighting is off.), “HOLD” (No DMX, lighting keeps the original state).
Display
The display reverse is used when the fixture is upside down.
Language
English or Chinese
Key Lock
When using the key lock function, not key operation after 30 seconds, the key is locked. Pressing the key in the locked state is invalid. It needs to press the MODE+SET key combination for 3 seconds to unlock.
Back Light
Select always on or 60S off if no operation
Reset
In order to verify whether the motor is working normally, and whether to save it after modifying the parameters, it can perform a reset operation, like repowering on.
Default
Restore the DMX address and parameters into factory values. The default address is 1, and the gray background option in the menu table is the default.
Calibrations
Enter 088 on the Password interface and press SET to enter the Calibrations menu. When the option on the left is selected, press the UP/DOWN button to select which function to operate. After pressing the SET button, the number on the right is in the selected state. At this time, press the UP/DOWN button to modify the value. Long press can be modified continuously. After pressing the SET button again, it changes back to the left option as the selected state.
Press the SET button on the Default option to restore the default value.
Information
Display the fixture software version and UID code of RDM.

DMX Channel

Function| DMX

Value

| Setting| 12 Channels
---|---|---|---
Dimmer| 000-255| 0~100%| 1
Strobe| 0-10| Always on| 2
11-127| Random strobe slow to fast
128-255| Linear strobe slow to fast
Color| 0~7| White| 3
8~15| Red
| 16~23| Green|
---|---|---|---
24~31| Blue
32~39| Yellow
40~47| Purple
48~55| Orange
56~63| UV
64~71| White+ Red
72~79| Red +Green
80~87| Green+ Blue
88~95| Blue+ Yellow
96~103| Yellow+ Purple
104~111| Purple + Orange
112~119| Orange + UV
120~127| UV +White
128~191| Clockwise rotation: fast to

slow

192~255| Counterclockwise rotation:

slow to fast

ColorF| 0-255| Color wheel positioning fine-

tuning

fast

72~79| Gobo 7 shake from slow to

fast

80~87| Gobo 6 shake from slow to

fast

88~95| Gobo 5 shake from slow to

fast

96~103| Gobo 4 shake from slow to

fast

104~111| Gobo 3 shake from slow to

fast

112~119| Gobo 2 shake from slow to

fast

| 120~127| Gobo 1 shake from slow to

fast

|
---|---|---|---
128~191| Clockwise rotation fast to

slow

192~255| Counterclockwise rotation

slow to fast

GoboR| 0~127| Static rotation by a certain

angle

| 6
128~191| Clockwise rotation fast to

slow

192~255| Counterclockwise rotation

slow to fast

GoboF| 0~255| Pattern positioning fine-

tuning

slow

192~255| Counterclockwise rotation

slow to fast

RDM Supported Parameters

Readable

| Writabl

e

| ****

RMD instruction

| ****

value

| ****

description

| customiz

e

---|---|---|---|---|---

| ****

DISC_UNIQUE_BRANCH

| 0x000

1

| ****

search

| ****

DISC_MUTE

| 0x000

2

| ****

Lock

| ****

DISC_UN_MUTE

| 0x000

3

| ****

Unlock

| ****

√

| ****

SUPPORTED_PARAMETER S

| ****

0x005

0

| Supported instruction

list

| ****

√

| ****

PARAMETER_DESCRIPTIO N

| ****

0x005

1

| Custom

instruction description

| ****

√

| ****

DEVICE_INFO

| 0x006

0

| Device

Information

| ****

---|---|---|---|---|---

√

| ****

DEVICE_MODEL_DESCRIP TION

| ****

0x008

0

| Product

model description

| ****

√

| ****

MANUFACTURER_LABEL

| 0x008

1

| manufactur

er

| ****

√

| ****

√

| ****

DEVICE_LABEL

| 0x008

2

| ****

Device label

| ****

√

| ****

√

| ****

FACTORY_DEFAULTS

| 0x009

0

| Factory

defaults

| ****

√

| ****

SOFTWARE_VERSION_LA BEL

| ****

0x00C

0

| Software version

description

| ****

√

| ****

√

| ****

DMX_START_ADDRESS

| 0x00F

0

| starting

address

| ****

√

| ****

SENSOR_DEFINITION

| 0x020

0

| Sensor

definition

| ****

√

| ****

√

| ****

SENSOR_VALUE

| 0x020

1

| ****

Sensor value

| ****

√

| ****

RECORD_SENSORS

| 0x020

2

| Record

sensor value

| ****

√

| ****

√

| ****

DISPLAY_INVERT

| 0x050

0

| Display

reversed

| ****

√

| ****

√

| ****

IDENTIFY_DEVICE

| 0x100

0

| Identify

device

| ****

√

| ****

RESET_DEVICE

| 0x100

1

| ****

Reset device

| ****

√

| ****

CAPTURE_PRESET

| 0x103

0

| Capture

preset

| ****

√

| ****

√

| ****

PRESET_PLAYBACK

| 0x103

1

| Preset

playback

| ****

√

| ****

√

| ****

FAC_RUN_MODE

| ****

0xD32

0

| Lamp operation

mode

| ****

√

| ****

√

| ****

FAC_SAVE_RUN_MODE

| ****

0xD32

1

| Save operating

mode

| ****

√

Instructions of lamp operation mode: data is 1 byte unsigned number, 0 means DMX mode, 1 means manual control mode, 2 means Auto run mode, 3 means slave mode.
Save operation mode description: The 0xD320 instruction is only a temporary modification of the operation mode. You need to use the 0xD321 instruction to save, write 1 to save the current operation mode, and write 0 to restore the previously stored operation mode.