sistema BEEZOOM740 7×40W LED Moving Head User Manual

: October 30, 2023
: Sistema

Table of Contents

Safety Instructions
Technical Specifications
How To Control The Unit
Trouble shooting
Fixture Cleaning
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEEZOOM740 7×40W LED Moving Head
User Manual sistema BEEZOOM740 7×40W LED Moving
Head

Statement
The product has well capability and intact packing when leave factory. All of the user should comply with warning item and manual, any misuse cause of the damages are not included in our guarantee, and also can not be responsible for any malfunction & problem owing to ignore the manual.

Safety Instructions

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also receive this instructionbooklet.

Unpack and check carefully there is no transportation damage before using the unit.
Before operating, ensure that the voltage and frequency of power supply match the power requirements of the unit.
It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
The unit is for indoor use only. Use only in a dry location.
The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent surfaces.
Be sure that no ventilation slots are blocked.
Disconnect main power before replacement or servicing.
Make sure there are no flammable materials close to the unit while operating as it is fire hazard.
Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always by taking its base.
Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher than this Unit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand during its operation. Turn off the power and allow about 15 minutes for the unit to cool down before replacing or serving.
In the event of serious operating problem, stop using the unit immediately.Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type spare parts.
DO NOT touch any wire during operation as high voltage might be causing electric shock.

Warning:

To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.
DO NOT open the unit within five minutes after switching off.
The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.

Caution:
There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any repairs yourself. In the unlikely event your unit may require service, please contact your nearest dealer.
Installation:
The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating.
And make sure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.
The equipment must be fixed by professionals. And it must be fixed at a place where is out of the touch of people and has no one pass by or under it.

Technical Specifications

Light Sources: 7x40W RGBW Original LED
Power Voltage: AC 100-240V, 50/60Hz, 500w
Single LED power: 40W
Color: RGBW automatic correction 16.7 million pixels
Electronic dimmer: 0～100% linear
Control
DMX Channel: 23/35/51 Channel
Control Modes: DMX512
Software Upgrade: Firmware update via DMX link
Pan/Tilt
Pan/Tilt: 540°
Construction
Display: LCD Display
Data In/Out socket: 3-pin XLR sockets Power Socket: Powercon in/out
Protection Rating: IP20
Features
Motorized liner zoom system,
zoom range: 4.5°~45° Outstanding color macro effect,CTO,Kaleido effects,led single controlled
Dimmer: 0~100% smooth dimming Variable strobe effects
Fast, quiet operation and flicker free/ 270° Pan/Tilt Resolution: 16 bit

How To Control The Unit

The DMX512 is widely used in intelligent lighting control,with a DMX 512 controller.connect several lights together,dmx in and dmx out, 3 pinXLR connectors:Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+) sistema BEEZOOM740 7×40W LED Moving Head - fig 1 Figure: 2
XLR Pin Configuration
pin1=Ground
pin2=Data Compliment(negative)
pin3=Data true(positivc)
Display:
MENU To select the programming functions DOWN To go backward in the selected functions uP To go forward in the selected functions ENTER To confirm the selected functions
Set DMX Address Code

Press “Menu” to “Set DMX Address”,and press”ENTER” keys to enter into Show “Set DMX Address DMX
Address: 001″,Press the “UP and DOWN” keys to amended
Press “ENTER”keys to save and Exit,Press the”MENU”Keys does not save and Exit

DMX channel´s functions and values (23/35/51 DMX channels):

Channel list(51 channels)

Trouble shooting

Following are a few common problems that may occur during operation. Here are some suggestions for easy troubleshooting:

The unit does not work, no light and the fan does not work
Check the connection of power and main fuse.
Measure the mains voltage on the main connector.
Check the power on LED.
Not responding to DMX controller
DMX LED should be on. If not, check DMX connectors, cables to see if link properly.
If the DMX LED is on and no response to the channel, check the address settings and DMX polarity.
If you have intermittent DMX signal problems, check the pins on connectors or on PCB of the unit or the previous one.
Try to use another DMX controller.
Check if the DMX cables run near or run alongside to high voltage cables that may cause damage or interference to DMX interface circuit.
One of the channels is not working well
The stepper motor might be damaged or the cable connected to the PCB is broken.

Fixture Cleaning

Thecleaning of internal and external optical lenses and/or mirrors must becarried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater accumulationofdirtontheunit’ soptics.

Clean with soft cloth using normal glass cleaning fluid.
Always dry the parts carefully.
Cleantheexternal optics atleast every 20 days.Cleanthe internal optics at least every 30/60 days.