AMGO LR06 Portable Low-Rise-D Lift Owner’s Manual

Original
Installation And Service Manual

Owner’s Manual
Portable Low-rised scissors lift
Model: LR06

PRODUCT FEATURES AND SPECIFICATIONS (See Fig.1)

PORTABLE LOW-RISED MODEL LROO

• Self-locking safety device: 3 stage safety lock, mechanical lock, automatic release.
• Portable unit is easy to move with the power unit stand
• High speed: From 0-23 5/8″ just 21 seconds
• Standard rubber pads induded

Fig. 1

MODEL LRO6 SPECIFICATIONS

Model| Lifting
Capacity| Raised
Height| Lifting
Time| Overall Length| Overall Width| Lowered
Height| Runway
Width| Runway
Length| Motor
---|---|---|---|---|---|---|---|---|---
LRO6| 600016s| 23 5/8″| 21S| 76 1/4″| 70″| 4 1/8″| 18″| 53 1/4″| 1.0 HP
Single Phase

INSTALLATION REQUIREMENT

A. Tools requirement

B. Power requirement
The electrical source must be 1.0HP minimum. The source cable size must be 2.5mm 2 and in good condition of contacting with floor.

STEPS OF INSTALLATION

A. Check the parts before assembly, make sure all the parts are completed.

1. Packaged lift, Parts box, Power Unit and Power Unit Stand.
   Move aside the parts, Open the outer packing and check the parts according to the shipment parts list (See Fig. 3).
   

2. Open the parts box, check the parts according to the part list (See Fig. 4).
   

3. Check the parts of the parts bag according to the parts bag list (See Fig. 5).

B. Install hydraulic power unit (See Fig. 6)

C. Install fitting to power unit, and then connecting oil hose (See Fig.7).

D. Install electrical system
Connect the power source on the data plate of power unit.

Note: For the safety of operators, the power wiring must contact the earth well.

Single phase motor

1. Circuit diagram (See Fig. 8)
   

2. Connection step (See Fig. 9)
   Connecting the two power supply wires (active wire L and neutral wire N) to terminals of AC contactor marked L1, L3 respectively. Earth wire( yellow and green wire) is connected with the earth wire terminal of the motor
   

EXPLODED VIEW

MODEL LRO6

Rollers

PARTS LIST FOR MODEL LRO6

PARTS FOR ROLLER
20-1| 11630031| Rollers handle| 2|
20-2| 10630032| Snap Ring (4)12| 8|
20-3| 11630033| Connecting Shaft (442’80| 2|
20-4| 11630034| Roller Shaft (i)12*65| 2|
20-5| 1003275021| White wheel| 4|

Cylinder

Manual Power Unit (071103)

Illustration of hydraulic valve for power unit

OPERATION INSTRUCTIONS

1. Install the oil hose between oil cylinder and power unit, connect well the power supply wire. The machine can be ready to use.

2. The roller must be disengage when lifting vehicle (See Fig.17). To raise and lock the lift: Press the button up till the lift is raised to the required height and the locks are in engaged (See Fig.15), then push release handle of the power unit, the lift would be locked.

3. Tolower lift: Press the button UP, until the safety lockis in the released position (See Fig.16), lower lift by pushing lowering handle.
   

4. Move lift: Pull up roller bracket, lock two roller to the lift with roller shaft. (See Fig. 16& 17 ). Moving the lift by the power unit stand.
   

1. There are four fixed holes in the machine, can fix the machine on ground by 3/4 X 5 1/2” anchor bolts (See Fig.19).

MAINTENANCE SCHEDULE

Monthly:

1. Lubricate all moving parts with lubricant.
2. Check all connectors, bolts and pins to insure proper mounting.
3. Make a visual inspection of all hydraulic hoses/lines for possible wear or leakage.

Every six months:

1. 1. Make a visual inspection of all moving parts for possible wear, interference or damage.
2. Check all fastener and re-torque.

Oil cylinder maintenance:

In order to extend the service life of the oil cylinder, please operate according to the following requirements.

1. Recommend to use N46 anti-wear hydraulic oil.
2. The hydraulic oil of the lifts should be replaced regularly during using. Replace the hydraulic oil 3 months after the first installation, Replace the hydraulic oil once a year afterwards.

TROUBLE SHOOTING

2. Wiring connections are not in good condition
3. Motor burned out
4. AC contactor burned out| 1. Replace start button
2. Repair all wiring connections
3. Repair or replace motor
4. Replace AC Contactor
Motor runs but the lift is not
raised| 1. Motor runs in reverse rotation
2. Gear Pump out of operation
3. Release Valve in damage
4. Relief Valve or Check Valve in damage
5. Low oil level
6. Overload or system low pressure| 1. Reverse two power wire
2. Repair or replace
3. Repair or replace
4. Repair or replace
5. Fill tank
6. Check load or adjusting the pressure of hydraulic system
Lift does not stay up| 1. Release Valve out of work
2. Relief Valve or Check Valve leakage
3. Cylinder or Fittings leaks| Repair or replace
Lift raises slowly| 1. Oil line is jammed
2. Motor running on low voltage
3. Oil mixed with air
4. Gear Pump leaks
5. Overload lifting| 1. Clean the oil line
2. Check electrical system
3. Fill tank
4. Repair or replace pump
5. Check load
Lift can not lower| 1. Safety device are in activated
2. Release valve in damage
3. Oil system is jammed| 1. Release the safeties
2. Repair or replace
3. Replace Clean the oil system

Lift disposal.

When the car lift cannot meet the requirements for normal use and needs to be disposed, it should follow local laws and regulations.

AMGO HYDRAULIC CORPORATION
1931 Joe Rogers Blvd, Manning, South Carolina,
Zip: 29102
Tel: (803) 505-6410
Fax: (803) 505-6410
Manual Part No. : 722215602
Revision Date: : 2022/02

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>