V-TAC VT-13 LED Dome Light With Pir Sensor Instruction Manual

: June 17, 2024
: V TAC

Table of Contents

TECHNICAL DATA
INTRODUCTION & WARRANTY
FUNCTION
INSTALLATION DIAGRAM
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

INSTRUCTION MANUAL
LED DOME LIGHT WITH PIR SENSOR

WEEE Number: 80133970

TECHNICAL DATA

MODEL	VT-13
SKU	21807, 21808, 21809
WATTS	12W
LUMENS	900 Lm (3000K)

INTRODUCTION & WARRANTY

Thank you for selecting and buying V-TAC product. V-TAC will serve you the best. Please read these instructions carefully before starting the installation and keep this manual handy for future reference. If you have any another query, please contact our dealer or local vendor from whom you have purchased the product. They are trained and ready to serve you at the best. The warranty is valid for 3 years from the date of purchase. The warranty does not apply to damage caused by incorrect installation or abnormal wear and tear. The company gives no warranty against damage to any surface due to incorrect removal and installation of the product. The products are suitable for 10-12 Hours Daily operation. Usage of product for 24 Hours a day would void the warranty. This product is warranted for manufacturing defects only.

WARNING

Please make sure to turn off the power before starting the installation.
The light source of this luminaire is not replaceable, when the light source reaches its end of life the whole luminaire should be replaced.
Installation must be performed by a qualiﬁed person.
For Indoor use only

FUNCTION

Can identify day and night: The consumer can adjust working state in difierent ambient light. It can work in the daytime and at night when LUX knob is adjusted on the “sun” position (max). It can work in the ambient light less than 3LUX when it is adjusted on the “moon” position (min). As for the adjustment pattern, please refer to the testing pattern.
Time-Delay is added continually: When it receives the second induction signals within the ﬁrst induction, it will restart to time from the moment.
Time-Delay is adjustable. It can be set according to the consumer’s desire. The minimum time is 10sec+3sec. The maximum is 3min±30sec.

IN CASE OF ANY QUERY/ISSUE WITH THE PRODUCT, PLEASE REACH OUT TO US AT: SUPPORT@V-TAC.EU
FOR MORE PRODUCTS RANGE, INQUIRY PLEASE CONTACT OUR DISTRIBUTOR OR NEAREST DEALERS.
V-TAC EUROPE LTD. BULGARIA, PLOVDIV 4000, BUL.L.KARAVELOW 9B

**** This marking indicates that this product should not be disposed of with other household wastes.
Caution, risk of electric shock.

V-TAC VT-13 LED Dome Light With Pir Sensor - Symbol 3

INSTALLATION DIAGRAM

Switch off the power
Remove the cover of the luminaire. (Refer to ﬁgure 1)
Find the wire hole in the bottom and pass the power wire through hole. Connect the power wire into connection-wire column according to the connection-wire diagram.
Fix the bottom with inﬂated screw on the selected position.
Switch of the power and test it

V-TAC VT-13 LED Dome Light With Pir Sensor - INSTALLATION
DIAGRAM

TEST

Turn the Time knob anti-clockwise on the minimum. Turn the TIME knob clockwise on the maximum (sun).
Switch on the power; the lamp will have no signal at the beginning. A«er Warm-up 30sec, the lamp will start to work. If it recceives the induction siganl, the lamp will turn on. While there is no another induction signal any more, the lamp should stop working within 10sec+3sec.
Turn LUX knob anti-clockwise on the minimum (moon). If the ambient light is more than 3LUX, the lamp should not work. If the ambient light is less than 3LUX (darkness), the sensor would work. Under no induction signal condition, the lamp should stop working winthin 10sec+3sec.

NOTE: When testing in daylight, please turn LUX knob to (SUN) position, otherwise the sensor lamp could not work!

Should be installed by qualiﬁed electrician.
Before installing please make sure the power is OFF to avoid electric shock.
Avoid installing it on uneven surface.
Avoid pointing the detector towards objects with highly reﬂective surfaces, such as mirrors etc.
Avoid mounting the detector near heat sources, such as heating vents, air conditioning units etc.
Avoid pointing the detector towards objects that may move in the wind, such as curtains, tall plants