MINKA LAVERY 2751-694 Ponderosa Ridge 1-Light Weathered Spruce and Silver Hardwired Outdoor Wall Lantern Sconce Instruction Manual

MINKA LAVERY 2751-694 Ponderosa Ridge 1-Light Weathered Spruce and Silver

Hardwired Outdoor Wall Lantern Sconce

Product Information

The product is an electrical fixture with item number 2751-694. It comes with a circular strap, ground screw, mounting screws, knurled knobs, rubber washers, and a large glass shade. The fixture requires installation and should be connected to a junction box. It is important to turn off the power at the fuse box or circuit breaker before installing the fixture. The product is intended for indoor use only.

Product Usage Instructions

1. Turn off the power at the fuse box or circuit breaker.
2. Carefully remove the old fixture and its mounting hardware.
3. Unpack the new fixture and lay out all the parts in a clean area.
4. Thread screws (C) into the pre-drilled holes in the circular strap (A) spaced the same distance apart as the holes in the back plate of the fixture body (D).
5. Attach the circular strap (A) to the junction box using mounting screws (B) with the side marked GND facing out.
6. Connect the electrical wires, making sure that all wire connectors are secured. Connect the fixture’s ground wire to either the junction box’s ground wire or directly to the circular strap (A) using the green screw provided.
7. Place fixture body (D) over screws (C) and secure with knurled knobs (E) and rubber washers (M) provided.
8. Place large glass shade (J) over socket (F) and twist to secure to the socket cup.
9. Turn on power at the fuse box or circuit breaker and test the fixture.

Note : The illustration in the manual (Fig. 1) is for installation purposes only and may or may not be identical to the fixture purchased.

WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.

Item #2751-694 (New. 2022/04/18)

MOUNTING THE FIXTURE

1. Shut of power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.

2. Carefully unpack your new fixture and lay out all the parts in a clean area. Take care not to misplace any small parts necessary for installation.

3. Thread screws (C) into the pre-drilled holes in the circular strap (A) spaced the same distance apart as the holes in the back plate of the fixture body (D). The length of screws (C) may be adjusted if necessary.

4. Attach the circular strap (A) to the junction box (not included) using mounting screws (B) (Size: #8-32N*L0.5”). The side of the circular strap marked “GND” must face out.
   CONNECTING THE WIRES

5. Connect the electrical wires as shown in figure 2,making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the circular strap (A) using the green screw provided. After the wires are connected, tuck them carefully inside the junction box.
   COMPLETING THE INSTALLATION

6. Place fixture body (D) over screws (C) and secure with knurled knobs (E) and rubber washers (M) provided.

7. To prevent moisture from entering the outlet box and causing a short, use clear caulking (i.e. Indoor/Outdoor Silicone Sealant) to outline the outside of fixture back-plate where it meets the wall leaving a space at bottom to allow moisture a means to escape (Fig.3).

8. Secure pine cone (K) to the metal stick on the fixture body (D).

9. Place small glass shade (G) over socket (F) and secure with socket ring (H) using socket spanner (I).

10. Install (1) one medium base bulb (L) up to 60 watts or CFL or LED equivalent (not included) in accordance with the fixture specification — DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)

11. Place large glass shade (J) over socket (F) and twist to secure to the socket cup.

Your installation is now complete. Return power to the junction box and test the fixture.

Note : Illustration (Fig. 1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>