PrismXR W1 Carina 30W Battery Pack User Guide

Quick Start Guide
PrismXR Carina W1 P1101
Discover more: www.prismxr.com

Support
For more information, please visit www.prismxr.com/pages/support

What’s In the Box

Product Introduction

The PrismXR Carina W1 is a 10,000mAh power bank specially designed for charging VR headsets. With a maximum power output of 30W, it ensures efficient charging. For  convenience and comfort, it can be worn around the waist or across the shoulder. Additionally, it offers broad compatibility with all USB Type-C devices, adhering to USB charging standards.

How to Assemble

1. Take the left strap and thread it through the bottom of the fixed loop.
   The fixed loop is on the left side of the Carina W1.

2. Fold the left strap over and insert it into the top of the fixed loop on the inner side.

3. Follow steps 1 and 2 to assemble the right strap in the same manner.

How to Wear

1. There are two ways to wear the Carina W1:
   a. Around the waist
   b. Across the shoulder

2. Fasten and unfasten the left and right straps using the magnetic buckle.

Note: During the wearing process, you may need to adjust the length of the strap to a suitable size.

How to Set Up the Cord Organizer

1. Remove the transparent sticker from the back of the cord organizer.
2. Attach the cord organizer to the center of the headband on the back of the VR headset.
3. Press the cord organizer for a few seconds to ensure it is securely attached to the strap.

Check the Battery Status of the Carina W1

Note: It is recommended that you press the power button to check the remaining power status of the Carina W1 before use.
The four LED indicators and the corresponding battery levels are as follows:

Charging Your VR Headset Using Carina W1

Note:

• When your VR headset is fully charged by the Carina W1, the Carina
  W1 will automatically turn off and stop charging.

• Press and hold the Power button for 3 seconds to turn off the
  Carina W1 and stop charging the VR headset. And press the Power button once to turn on Carina W1 again and continue charging your VR headset.

1. Insert the USB-C charging cable into the Carina W1.

2. Insert the L-shaped USB-C connector of the charging cable into VR headset, Carina W1 will automatically turn on and charge your VR headset.

3. Thread the charging cable through the cord organizer and secure it at the back.

4. Put on your Carina W1.

Note: If you find the charging cable too long, you can adjust its length using the reusable cable tie provided.

Charging the Carina W1

Note:

• After the Carina W1 is fully charged, the four LED indicators will turn off.
• To charge the Carina W1, you will need to use an adapter (not provided). The maximum supported charging power is 18W, and it is compatible with charging inputs such as 5V/3A, 9V/2A, 12V/1.5A, etc.

1. Connect the Carina W1 to the power adapter.
2. The four LED indicators and the corresponding battery charge levels are as follows:

Clean the Carina W1

Note:

• Do not use washing machines or dryers.
• Make sure the liquid is alcohol free.

1. Take off the left and right straps from Carina W1.
   

2. Hand wash the two straps in clean water (you can use laundry detergent if needed).

3. Allow the two straps to air dry naturally (do not wring them by hand).

4. Put them back after they are fully dry.

Specifications

Safety Instructions

When using this product, basic precautions should always be followed, including the following:

• Do not bend the Carina W1 frequently.
• Clean the Carina W1 with a soft, dry cloth. Make sure the liquid is alcohol free.
• You can take off the straps and wash them (do not use washing machines or dryers). Put them back after they are fully dry.
• Carina W1 is not waterproof and should not be rinsed under running water or submerged in an ultrasonic cleaner.
• Store product in a cool and dry place.
• Do not store the product in a hot or humid environment.
• The operating temperature should be between 32°F to 113°F (0°C to 45°C).
• Do not disassemble the product. Take it to a qualified service person when service or repair is required. Incorrect reassembly may result in a risk of fire or injury to persons.
• If the product is not used for long periods of time, you should change and discharge it once every three months.
• When charging a device, the front side of the product may feel warm.This is a normal operating condition and should not be cause of concern.
• In normal conditions, the battery performance will decline over several years.
• Do not dispose of the product in heat or fire.
• Do not clean the product with harmful chemicals or detergents.
• Misuse, dropping or excessive force may cause product damage.
• When disposing of secondary cells or batteries, keep cells or batteries of different electrochemical systems separate from each other. Before disposal, cover the battery connector with electrical insulating tape.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio / TV technician for help.

The following importer is the responsible party.
Company Name: PRISMXR PTE, LTD
Address: 60 PAYA LEBAR ROAD #12-03 PAYA LEBAR SQUARE
SINGAPORE, 409051

IC Statement
This device complies with Industry Canada license ‐ICES-003.
Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.

References

• PrismXR Official Website – PrismXR
• Support – PrismXR

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>