cudy WR2100 Gigabit Dualband WLAN Mesh Router Installation Guide
- June 3, 2024
- cudy
Table of Contents
WR2100 Gigabit Dualband WLAN Mesh Router
Installation Guide Quick Installation Guide
WR2100 Gigabit Dualband WLAN Mesh Router
Email: support@cudy.com
**** Website: www.cudy.com
If your internet connection is through an ethernet cable directly from the
wall instead of through a DSL/Cable/Satellite modem, connect the ethernet
cable to the router’s
WAN port, and skip steps 1, 2 ,3.
-
Turn off the modem, and remove the battery if it has one.
-
Connect router’s INTERNET Port to DSL/Cable Modem/Ethernet.
-
Turn on the modem and then wait about 2 minutes for it to restart.
-
Connect the power adapter to the router, and wait 1 minute until the system LED changes from flashing to solid on red or blue , which means that the system startup is completed.
-
Connect your computer to the router (Wired or Wireless)
Wired
Turn off the Wi-Fi on your computer and connect it to router’s LAN port via an ethernet cable.
Wireless
Connect your device to the router’s Wi-Fi using the SSID (network name) and Password printed on the bottom of the router.
-
Launch a web browser, and enter http://cudy.net/ or http://192.168.10.1/ in the address bar. Use admin for password to log in.
Note: If the login window does not appear, please refer to FAQ > Q1 -
Then below popup will appear, please follow step by step instructions to set up the internet connections.
Note: If the pop-up window does not appear, please click Quick Setup on the status page.
LED and Button
| Name | Status | Indication |
|---|
System
LED| Solid On| Red| Internet is not connected
Blue| Internet is connected
Flashing| Red| System is starting up
Blue| WPS is in progress
Red-Purple-Blue| Software upgrading
Off| Power adapter is not connected to the device.
Ethernet
LED| On| The corresponding ethernet port is connected.
Off| The corresponding ethernet port is not connected.
Button| WPS| Press and hold 1 second to enable the WPS function.
Reset| Press and hold 6 seconds to reset the router to its factory default
settings.
Support
For technical support,the user guide and more information, please visit:
http://www.cudy.com/support
support@cudy.com
Frequently Asked Questions (FAQ)
Q1: What can I do if the login window does not appear?****
– A1: If the computer is set to a static IP address, change its settings to
obtain an IP address and DNS server address automatically.
– A2: Verify that http://cudy.net/ or 192.168.10.1 is correctly entered in
the web browser.
– A3: Use another web browser and try again.
– A4: Reboot your router and try again.
– A5: Disable and then enable the network adapter being used.
Q2: What should I do if i can not find Wi-Fi signal?****
– A: Please make sure the router is connected, power and broadband interface has no loose. If everything is normal but still no signal, please try to use computer to set, or restore the router to factory settings. If after restoring factory settings but still no signal, you can restart the router, if it still doesn’t work, maybe the router has fault.
Q3: How to Reset to defaults?****
– A: While the power is still on, keep pressing the reset button for 6 seconds, and wait for 1-2 minutes and it will restore to factory settings.
Q4: Why can’t my mobile phone enter the Setting Page of Router?****
– A: Please make sure your mobile phone is connected to the Cudy Router Wi- Fi(default name is printed on the buttom of router), and make sure you enter the right site in the browser. (Please follow instructions FAQ -> Q1)
Q5: Why can’t I enter the setting page after restarting the Router?****
– A: After restarting the Router, maybe your phone or computer connect automatically to other Wi-Fi, please make sure your phone or computer is connected to Cudy Router Wi-Fi. (default name is printed on the bottom of router)
Enjoy the internet!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>