lionelo Flower Travel Bed User Manual

: June 12, 2024
: lionelo

Table of Contents

lionelo Flower Travel Bed
Product Information
Product Usage Instructions
IMPORTANT, RETAIN FOR FUTURE REFERENCE
Assembly instruction
Cleaning
Read User Manual Online (PDF format)
Download This Manual (PDF format)

lionelo Flower Travel Bed

lionelo-Flower-Travel-Bed-product

Product Information

The product is a Flower Travel Bed manufactured by BrandLine Group Sp. z o. o., located in Pozna, Poland. The product is designed to provide a safe and comfortable sleeping environment for babies during travel. The product comes with a changing table and organizer for added convenience. The product has been tested and meets all the requirements of EN 716-1:2017+AC:2019, and EN 12221-1:2008+A1:2013.

Product dimensions: Not specified
Weight: Not specified
Manufacturer: BrandLine Group Sp. z o. o.
Manufacturer Address: ul. A. Krglewskiego 1, 61-248 Pozna, Poland

Product Usage Instructions

Important Safety Instructions:

The assembly of the product must be performed by an adult.
Do not leave the child unattended on the changing pad.
Do not use electric bar fires, gas fires, etc. in the near vicinity of the changing unit.

Assembly Instructions

Take the travel baby bed out of the bag and loosen the adhesive straps. Place the bed on the floor and put the bag aside (see Fig. 1).
Separate the legs pulling them apart. Keep the central lock up. Otherwise, handrails will not fit in the right place (see Fig. 2).
Pull the middle part of each top rail covered with material so that they fit into place. Start with the longer rails, and then the shorter ones (see Fig. 3).
Push the middle lock until the surface is completely flat (you will hear the click sound) (see Fig. 4).
Mount the platform with the zipper (fig. 5). Secure the zipper by fastening the clasp (see Figure 5a). Connect the stiffening pipes located at the bottom of the platform together (Fig. 6). Place the mattress on a platform and connect it to the platform with Velcro.
Push the button marked in fig. 7 and connect short and long stiffening tubes of the changing table. Install the plastic fastening elements on the long and short sides of the bed.
Put the hooks on the organizer and mount it on the bed frame.

Baby Bed Folding Instructions

Remove all the bed accessories. Remove the mattress, canopy, organizer and all the other accessories. Grasp the centre handle located in the middle of the floor and pull it up.
To unlock the upper rails, press the indicated buttons on each side of them. Pull it slightly up and then push it down. Unlock the shorter sides first, and then do the same with the longer ones.
While still pulling up the handle, lift the floor of the baby bed and fold the legs.
Wrap the folded bed with the mattress and fasten it with Velcro straps. Put the folded baby bed into the bag. If the installation is unsuccessful, repeat the whole process again until the submission

Cleaning Instructions
Wipe the product with a damp cloth, then allow to dry. Changing table – clean with warm water and mild soap. Do not dry clean and do not use caustic agents. Do not dry mechanically, do not iron.

Dear Customer!
In case of any questions or comments on the purchased product, please contact us: help@lionelo.com

IMPORTANT! KEEP THESE INSTRUCTIONS FOR FUTURE USE.

NOTE: THE ASSEMBLY OF THE PRODUCT MUST BE PERFORMED BY AN ADULT.
Failure to comply with this provision and the assembly instructions could result in serious injury or even death.

Producer:
BrandLine Group Sp. z o. o.
ul. A. Kręglewskiego 1, 61-248 Poznań, Poland

IMPORTANT, RETAIN FOR FUTURE REFERENCE

READ CAREFULLY

WARNING

Be aware of the risk of open fire and other sources of strong heat, such as electric bar fires, gas fires, etc. in the vicinity of the cot.
Do not use the cot if any part is broken, torn or missing and use only spare parts approved by the manufacturer.
Do not leave anything in the cot or place the cot close to another product, which could provide a foothold or present a danger of suffocation or strangulation, e. g. strings, blind / curtain cords.
Do not use more than one mattress in the cot.
The cot is ready for use only when the locking mechanisms are engaged. Check carefully that they are fully engaged before using the folding cot.
The lowest position is safest. The base should always be used in that position as soon as the baby is old enough to sit up.
The upper position of the cot is suitable for children weighing up to 9 kg. If your child starts to sit down himself, use only the lower position.
If you leave the child unattended in the crib, always make sure that the side entrance is fastened with a zipper.
It is essential to remove detachable support rails before the cot is used in the lowest position.
All assembly fittings should always be tightened properly and fittings should be checked regularly and retightened as necessary.
To prevent injuries from falls: when the child is able to climb out of the cot, the cot shall no longer be used for that child.
The product is intended for children aged 0+ to 36 months and weighing up to 15 kg.
WARNING – Only use the mattress sold with this cot, do not add a second mattress on this one, suffocation hazards.
The mattress is an integral part of the bed.
The mattress should be inserted with the Velcro down.

CHANGING PAD WARNING
Do not leave the child unattended.

The baby cots should be blocked before using the changing table.
The changing table is suitable for children up to 12 months of age and weighing up to 11 kg.
Any additional or replacement parts can only be obtained from the manufacturer.
Do not use the changing unit when any part is broken, torn or missing.
Be aware of the risk of open fires and other sources of strong heat, such as electric bar fires, gas fires, etc. in the near vicinity of the changing unit.

Assembly instruction

Take the travel baby bed out of the bag and loosen the adhesive straps. Place the bed on the floor and put the bag aside (see Fig. 1).
Separate the legs pulling them apart. Keep the central lock up. Otherwise, handrails will not fit in the right place (see Fig. 2).
Note! So that the sides of the cot/handrails are properly blocked, the central blockade of the floor must be raised upwards. The baby rails will not lock when the floor is unfolded.
Pull the middle part of each top rail covered with material so that they fit into place. Start with the longer rails, and then the shorter ones (see Fig. 3).
Push the middle lock until the surface is completely flat (you will hear the click sound) (see Fig. 4).

$lionelo-Flower-Travel-Bed-fig- $3$$ $lionelo-Flower- Travel-Bed-fig- $4$$

Base installation
Mount the platform with the zipper (fig. 5). Secure the zipper by fastening the clasp (see Figure 5a). Connect the stiffening pipes located at the bottom of the platform together (Fig. 6). Place the mattress on a platform and connect it to the platform with Velcro.

Changing table assembly instruction
Push the button marked in Fig. 7 and connect short and long stiffening tubes of the changing table. Install the plastic fastening elements on the long and short sides of the bed.

Organizer installation
Put the hooks on the organizer and mount it on the bed frame.

Baby bed folding instruction

Remove all the bed accessories. Remove the mattress, canopy, organizer, and all the other accessories. Grasp the center handle located in the middle of the floor and pull it up.
To unlock the upper rails, press the indicated buttons on each side of them. Pull it slightly up and then push it down. Unlock the shorter sides first, and then do the same with the longer ones.
While still pulling up the handle, lift the floor of the baby bed and fold the legs.
Wrap the folded bed with the mattress and fasten it with Velcro straps. Put the folded baby bed into the bag. If the installation is unsuccessful, repeat the whole process again until submission