CRYSTORAMA ARA-10265-SB Aragon LED Chandelier Instruction Manual

CRYSTORAMA ARA-10265-SB Aragon LED Chandelier

Product Information

The product is a lighting fixture called “CRYS T RAMA” which has been in the market for sixty years. The model number of the fixture is ARA-10265-SB. It is a dry-rated fixture that requires a 10-G9 LED bulb with a maximum of 3.5 watts for extended use. The electrical components of the fixture must be installed by a licensed electrician in accordance with the National Electric Code and appropriate local electrical codes.

Product Usage Instructions

1. Before installing or changing the bulb, turn off the power to the fixture.
2. Use a licensed electrician to install the electrical components of the fixture in accordance with the National Electric Code and appropriate local electrical codes.
3. Insert the 10-G9 LED bulb into the fixture.
4. Do not exceed the maximum wattage of 3.5 watts for the LED bulb.
5. Turn on the power to the fixture and enjoy the light.

ASSEMBLY INSTRUCTION MODEL #ARA-10265-SB

WARNING

• All electrical components must be installed by a licensed electrician in accordance with the National Electric Code and the appropriate local electrical codes.

• You will need 10-G9 LED BulbLED 3.5 Watts Max. USE LED BULBS FOR EXTENDED USE THIS FIXTURE IS DRY-RATED.

How to install for hanging

• Please place the fixture frame on a soft cloth-covered table before the installation.

1. Insert one end of a side rod into the coupler on the inside of the frame ring and secure it with a set screw using the Allen wrench. Tighten the screw until it is flush with the rod. Do not over-tighten the screw. Repeat for the other side rods.
2. Insert the other end of a side rod into the coupler on the wire box and secure it with a set screw using the Allen wrench. Tighten the screw until it is flush with the rod. Do not over-tighten the screw. Repeat for the other side rods.
3. Decide the preferred hanging height and choose the rods needed.
4. Slip the wire through the rods and connect them together Screw one end of the rod assembly onto the top of the wire box and the other end onto the swivel on the mounting bar.
5. Install the mounting plate to the outlet box and raise the fixture up and do the wire connections. Raise the canopy up over the outlet box and secure it with the collar ring.
6. Slide the rubber washer over the socket, place the crystal shade and check ring over the socket and secure it with the socket ring using the wrench.
7. Install the G9 led bulb into the socket.

The glass can be installed facing either up or down. Please decide the preferred direction before installing the rod onto the frame.

WARNING: This product can expose you to Lead which is known to the state of California to cause cancer and/or birth defects or reproductive harm. For more information go to www.P65Warnings.ca.gov.

Part Number

• A. Mounting Hardware
  • (1) Mounting Bar
  • (2) Wire Nut
  • (2) Outlet Box Screw
• B. (1) Swivel
• C. (1) Canopy W5″ *H1″; XME10264SBCAN5IN
• D. (1) Collar Ring
• E. (3) Rod W2″ *H12″; XMEI0264SBROD12IN
• F. (1) Rod W2″ *H6″; XME10246SBROD6IN
• G. (1) Wire Box
• H. (10) Rod, XME10265SBSIDEROD
• I. (10) Socket
• J. (10) Rubber washer
• K. (10) Crystal Shade W4 %”*H3 H”; XME10264SGLA4. 31N
• L. (10) Check ring
• M. (10) Socket ring
• N. (10) LED Bulb
• 0. (1) Wrench
• P. (1) Allen Wrench

Crystorama.com.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>