Minka Lavery 2453-695 Bishop Crossing 24.5 Inch 3 Light Soft Brass Vanity Light Instruction Manual

Minka Lavery 2453-695 Bishop Crossing 24.5 Inch 3 Light Soft Brass Vanity

Light

Product Information

The product being installed is item #2453-695, manufactured on August 13, 2021. The product is a light fixture that requires installation onto a wall junction box. The fixture includes amounting plate, drywall anchors, mounting screws, wood screws, anda shade assembly. The fixture is designed to hold three medium base bulbs of up to 60 watts each or CFL or LED equivalent bulbs (not included).

Product Usage Instructions

1. Shut off power at the fuse box or circuit breaker box.
2. Remove the old fixture, including the mounting hardware.
3. Unpack the new fixture and lay out all the parts in a clear area.
4. Loosen screws (E) to remove mounting plate (A) from fixture body (F).
5. Position mounting plate (A) on the wall and mark the location of two drywall anchors (B). Pre-drill the holes for the drywall anchors (B). Insert drywall anchors (B) into the wall.
6. Attach mounting plate (A) to the junction box using the mounting screws (D). The side of mounting plate (A) marked GND must face out.
7. Connect the electrical wires as shown in Fig. 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (A) using the green screw provided. After the wires are connected, tuck them carefully inside the junction box.
8. Place fixture body (F) over the mounting plate (A) and secure with screws (E).
9. Place shade assembly (J) onto socket stand (G) and secure with screws (I).
10. Install three medium base bulbs (H) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification. DO NOT EXCEED THE MAXIMUM WATTAGE RATING!
11. Turn on power at the fuse box or circuit breaker box and test the fixture.

INSTALLATION INSTRUCTIONS

• Item#2453-695 (New. 2021/8/13)

READ AND SAVE THESE INSTRUCTIONS

WARNING! SHUT THE POWER OFF AT THE FUSE OR CIRCUIT BREAKER.
AVERTISSEMENT! COUPER LE COURANT U NIVEAU DES FUSIBLE OU DU DISJONCTEUR.

MOUNTING THE FIXTURE

Set#A-021-468112

• Mounting Screw*2
• Ground Screw
• Mounting Plate

1. Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.

2. Carefully unpack your new fixture and lay out all the parts in a clear area. Take care not to misplace any small parts necessary for installation.

3. Loosen screws (E) to remove mounting plate (A) from fixture body (F).

4. Position mounting plate (A) on the wall and mark the location of two drywall anchors (B). Pre-drill the holes for the drywall anchors (B). Insert drywall anchors (B) into the wall.

5. Attach mounting plate (A) to the junction box (not included) using the mounting screws (D). The side of mounting plate (A) marked “GND” must face out.

6. Place woodscrews (C) through the holes into the drywall anchor (B) to secure mounting plate (A) as shown in Fig.1.
   CONNECTING THE WIRES

7. Connect the electrical wires as shown in Fig. 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (A) using the green screw provided. After the wires are connected, tuck them carefully inside the junction box.
   FINISHING THE INSTALLATION

8. Place fixture body (F) over the mounting plate (A) and secure with screws (E).

9. Place shade assembly (J) onto socket stand (G) and secure with screws (I).

10. Install (3) three medium base bulbs (H) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification. —DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)

Your installation is now complete. Return power and test the fixture.
Note: The illustration (Fig.1) in this manual is for installation purposes only. It may or may not be identical to the fixture purchased.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>