MINKA LAVERY 2959-572 Upham Estates 10-Light Coal and Polished Nickel Island Chandelier Installation Guide
- October 30, 2023
- MINKA LAVERY
Table of Contents
MINKA LAVERY 2959-572 Upham Estates 10-Light Coal and Polished Nickel
Island Chandelier
Product Information
The item number for this product is 2959-572, and it was manufactured on August 18, 2021. The product comes with installation instructions that should be read and saved for future reference. This fixture requires a power source and should be installed by a professional electrician. The maximum wattage rating for this fixture is 60 watts.
Product Usage Instructions
Before starting the installation process, shut off the power at the fuse box or circuit breaker box. Remove the old fixture and mounting hardware, then unpack the new fixture and lay out all the parts in a clean area.
To assemble the fixture, first, loosen the hex nuts on the canopy with a wrench and remove the metal washer, lock washer, canopy, and swivels. Next, place the cloth shade and metal washer over all thread. Determine the desired hanging height and thread the rods to all thread of fixture body. Pass wires through each rod during assembly and secure swivels onto rods. Slide canopy and metal plate followed by lock washer and metal washer onto swivels and secure with hex nuts via wrench.
Position the mounting plate on the ceiling and mark the location of the two drywall anchors. Pre-drill holes for drywall anchors, then insert drywall anchors into the ceiling. Attach the mounting plate to a junction box using mounting screws and wood screws into drywall anchors. The side of the mounting plate marked GND must face out.
To connect the wires, follow the instructions shown in Fig. 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate using the green screw provided. Tuck wire connectors neatly into the junction box.
To complete the installation, slide the canopy over the mounting plate and secure it with screws. Place candle covers over sockets, and install ten candelabra base bulbs up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification. Do not exceed the maximum wattage rating. The installation is now complete. Return power to the junction box and test the fixture.
Item#2959-572 (New. 2021/08/18)
READ AND SAVE THESE INSTRUCTIONS
WARNING! SHUT POWER OF F AT FUSE OR CIRCUIT BREAKER .
PREPARATION (Fig. 1)
-
Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.
-
Carefully unpack your new fixture and lay out all the parts in a clean area. Take care not to misplace any small parts necessary for installation.
ASSEMBLING THE FIXTURE (Fig. 1) -
Loosen hex nuts (D) on canopy (H) with wrench (J) (not included) and remove metal washer (E), lock washer (L), canopy (H) and swivels (G).
-
Place cloth shade (N) and metal washer (M) over all thread (T).
-
Determine the desired hanging height and thread rods (F1, F2 and F3) to all thread (T) of fixture body. Carefully pass wires through each rod during assembly. Secure swivels (G) onto rods (F1).
-
Slide canopy (H) and metal plate (I) followed by lock washer
(L) and metal washer (E) onto swivels (G) and secure with hex nuts (D) via wrench (J) (not included). -
Position mounting plate (A) on ceiling and mark the location of the two drywall anchors (K). Pre-drill holes for drywall anchors (K). Then insert drywall anchors (K) into ceiling.
-
Attach mounting plate (A) to junction box (not included) using mounting screws (B) (Size: #8-32N*L0.5”) and wood screws
(O) into drywall anchors (K). The side of the mounting plate marked “GND” must face out.
CONNECTING THE WIRES (Fig. 2)
-
Connect the electrical wires as shown in Fig. 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (A) using the green screw provided.
-
. Tuck wire connectors neatly into junction box. COMPLETING THE INSTALLATION (Fig. 1)
-
Slide canopy (H) over mounting plate (A) and secure with screws (C).
-
Place candle covers (Q) over sockets (R).
-
Install (10) ten candelabra base bulbs (P) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification—DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)
Your installation is now complete. Return power to the junction box and test
the fixture.
Note: Illustration (Fig. 1) on this manual is for installation purposes
only. It may or may not be identical to the fixture purchased.
LA-3483E
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>