Application Note #815
RadioRA 3 Demo Kit System and App Programming

RR-PROC3-KIT RadioRA 3 Demo Kit System and App Programming

How to add a processor to a RadioRA 3 demo kit for demonstration of system and app-based control
This application note is intended to provide guidance for programming a full- system demo kit using a RadioRA 3 demo kit and a RadioRA 3 processor. System programming is achieved by using Lutron Designer software and the PRO Installer mode of the Lutron app.
Adding a RadioRA 3 processor and creating a full-system demonstration tool To add a RadioRA 3 processor and create a full-system demonstration tool, the following is needed:

• A RadioRA 3 processor; RR-PROC3-KIT recommended

• An active, hardwired internet connection

• Access to the RadioRA 3 software

• An active myLutron account and the Lutron app

• Note: A hardwired internet connection is required for any cloud-based functions, including programming and control from the Lutron app.

  1. Create a new RadioRA 3 project file for your system demo using the Lutron Designer software. Add the following devices, present in the demo kit, to your project file:
     a. One “Sunnata PRO LED+ Dimmer”
     b. One “RF Sunnata 4-Button Keypad”
     c. One “RF Sunnata 3-Button Keypad with Raise/Lower”
     d. One “RF Sunnata 2-Button Keypad”
     e. One “Sunnata Companion Switch”

  2.  Add the desired programming to all devices. Once programming is added, begin activating the devices as they would be activated in any RadioRA 3 system. Once all devices have been activated and programming is transferred, then the RadioRA 3 demo kit is ready to be used to demonstrate system operation, including any Lutron app controls.
     For more information about adding and programming devices in the Lutron Designer software, see online training modules “Software Design – Add Controls & Equipment (OVW 753)”, and “Software Programming – Keypads (OVW 755)”.

Example of demo devices ganged together in the RadioRA 3 software
Note: Once activated within a RadioRA 3 system, the demo kit devices will no longer behave in demo mode, and they will need to be within wireless range of their respective RadioRA 3 processor for proper system functionality.
Returning the demo kit to standalone operation
Note: If demo kit devices are to be removed from the RadioRA 3 system and returned to use as a standalone demo, follow these steps:

1. Devices must first be reset to the factory settings.
2. For keypads, press and hold the main 2, 3, or 4 buttons on the keypad simultaneously, as shown below. Continue to hold the buttons for about 15 seconds, then release.
3. The keypad should now be back in “demo mode”. Simply test demo mode by pressing the keypad buttons.

Note: “Demo mode” does not apply to the Sunnata PRO LED+ Dimmer and the accompanying companion switch.
These devices will behave normally once they are deactivated.
Note: Depending on the type of lamp used in the kit, the dimmer may require manual adjustment to achieve optimum dimming characteristics following factory reset of the device. If dimming issues are noted, follow the steps in the dimmer’s installation instructions for “Setup for use WITHOUT a system” to adjust low-end trim, and/or phase dimming mode (forward-phase vs. reverse- phase) as required.
Lutron, RadioRA, and Sunnata are trademarks or registered trademarks of Lutron Electronics Co., Inc. in the US and/or other countries.
Lutron Contact Numbers

WORLD HEADQUARTERS:
USA
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299
TEL: +1.610.282.3800
FAX: +1.610.282.1243
support@lutron.com
www.lutron.com/support
North & South America
Customer Assistance
USA, Canada, Caribbean:
1.844.LUTRON1 (1.844.588.7661)
Mexico: +1.888.235.2910
Central/South America: +1.610.282.6701| UK AND EUROPE: Lutron EA Limited
125 Finsbury Pavement
4th floor, London EC2A 1NQ
United Kingdom
TEL: +44.(0)20.7702.0657
FAX: +44.(0)20.7480.6899
FREEPHONE (UK): 0800.282.107
Technical Support: +44.(0)20.7680.4481
lutronlondon@lutron.com| ASIA: Lutron GL Ltd.
390 Havelock Road

07-04 King’s Centre

Singapore 169662
TEL: +65.6220.4666
FAX: +65.6220.4333
Technical Support: 800.120.4491
lutronsea@lutron.com
Asia Technical Hotlines
Northern China: 10.800.712.1536
Southern China: 10.800.120.1536
Hong Kong: 800.901.849
Indonesia: 001.803.011.3994
Japan: +81.3.5575.8411
Macau: 0800.401
Taiwan: 00.801.137.737
Thailand: 001.800.120.665853
Other Countries: +65.6220.4666
---|---|---

Customer Assistance — 1.844.LUTRON1
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299 U.S.A.
P/N 048815 Rev. A 02/2023

Documents / Resources

| LUTRON RR-PROC3-KIT RadioRA 3 Demo Kit System and App Programming [pdf] Instructions
RR-PROC3-KIT RadioRA 3 Demo Kit System and App Programming, RR-PROC3-KIT, RadioRA 3 Demo Kit System and App Programming, Kit System and App Programming, App Programming, Programming
---|---

References

• Lutron Support Center | Lutron

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>