PHILLIPS CONNECT 77-S263 Cargo Vision Puck User Manual

: May 15, 2024
: PHILLIPS CONNECT

Table of Contents

INTRODUCTION
GENERAL FEATURE
SPECIFICATIONS
MECHANICAL DRAWING
FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT
INDUSTRY CANADA STATEMENT
COMPANY INFORMATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

User Manual
CargoVision Puck™
Part#: 77-S263

INTRODUCTION

The Phillips Connect CargoVision Puck™ Camera is one of a growing family of sensors and system monitoring products from Phillips Connect, used in conjunction with a PCT Gateway and Remote Listener System, or other cloud- based reporting system. CargoVision Puck is designed to provide an uncompromised, on-demand view of the interior of a trailer in 1080P quality.
Simple installation and connectivity to your existing Phillips Connect Trailer Gateway module provides the ability to pre-program image capture events based on motion, door open/closed (if equipped), timebased or web-based image on- demand. Images are uploaded to the cloud for viewing through the Phillips Connect customer portal or automated API feed.

GENERAL FEATURE

Environmental Resistance: IP67
Operational Temperature: -40°C to 65°C
Installation Time: ~15 minutes
Connectivity: BLE 2.4 GHz (to PCT Gateway module)
Image Quality: 1080P

SPECIFICATIONS

IMAGE PROPERTIES
Max resolution: 1920 x 1080
Field of View: 170°
Flash: White LED illumination
GATEWAY DATA INTERFACE
Bluetooth 4.2
ELECTRICAL
Input voltage range: 10 VDC to 14 VDC
Peak current draw from telematics: 300 mA @ 12 VDC 4-pin round connector
ENVIRONMENTAL
Ingress Protection Rating: IP67
Operating Temperature: –40°F to 149°F (–40°C to 65°C)
Storage Temperature: -40°F to 149°F (-40°C to 65°C)
MECHANICAL
Dimensions: 3.9” (H) x 1.97” (W) x 3.9” (D) (99 mm x 50 mm x 99 mm) Weight: 0.40 lbs. (180 g)

MECHANICAL DRAWING

PHILLIPS CONNECT 77 S263 Cargo Vision Puck - rear
view1

FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

FCC Caution : Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
IMPORTANT NOTE: FCC Radiation Exposure Statement
This equipment complies with the FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
The transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

INDUSTRY CANADA STATEMENT

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). operation is subject to the following two conditions:

This device may not cause interference
This device must accept any interference, including interference that may cause undesired operation of the device.

Radiation Exposure Statement:
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.