Sboard-III WIFI Single Door Controller Board User Manual
- June 14, 2024
- Sboard-III
Table of Contents
Sboard-III WIFI Single Door Controller Board
INTRODUCTION
The controller is a mini single door controller panel, can work with any Wiegand 26~44, 56, 58bits output reader, it uses Atmel microcontroller to assure stable performance, and equips with an infrared remote control for easy operation. The device supports 1,000 users, all user data can be transferred.
Two versions available
- Standalone Controller
- WiFi Controller with Tuye APP
FEATURES
Controller
- 12V DC power input
- One relay, 1000 users
- Multi access modes: Card. Card or PIN, and multi Gard’s/PINs
- Wiegand 26-44, 56, 58bits input
- Can connect with any raider with Wiegand 26-44, 56, 58bits output
- Can connect with any keypad raider with 4bits, 8bits (ASCII), or 1 Obits Virtual number output
- User data can be transferred (except fingerprint users)
- 2 devises can be interlocked for 2 doors
- Can connect with external alarm and door contact
- Support Master Card and Authorized User
APP Feature: (Only available for WIFI version)
- 500 APP users
- iOS and Android available
- Add / Delete users by APP (Only available for card users)
- Can set Time Restrictic11for users
- Temporary Code (One-time Or Period Code)
- Support checking Opening Record
- Remotely Access (Support 3Gl4G/5GJ
- Multiple Access Medes : Smartphone, Card, PIN, Fingerprint
- Doorbell Call Notice (Support External Door Bell)
Specifications
Carton Inventory
INSTALLATION
Wiring
Sound and Light Indication
Connection Diagram
Note: For WiFi version, it’s necessary to connect a ‘Door Contact’ for monitoring the door status in the APP.
When Use NO/NC/COM Dry Contact Output 
Remark
The power supply’s voltage must be the same with lock’s supply voltage, or
else, the lock will not work properly or be damaged.
PROGRAMMING
Programming will be vary depending on access configuration. Follow the instructions according to your access configuration.
Notes
- Remote Control; Please use the Infrared Remote Control to program the Controller, “IR” on the Controller is the infrared receiving window, please direct the Remote Control to It.
- Cards can be read on the RFID/Keypad/Fingerprint raiders only.
- PINs can be input Added on either the remote control or the external Keypad Reader, QxCQpt when the Keypad Reader is 10 digits bilabial card number output, the PIN(.a) can only be input/acceded through the Keypad Reader.
User ID number: Assign a user ID to the user in order to track it
- The Common user ID : 0-986
- Authorized User ID : 987
- Panic User ID: 988-989
- Visitor U8″r ID : 990-999
- IMPORTANT : User IDs do not have to be processed with any leading zeros.
- Recording of User ID i:1 critical.
- PIN: can be any 4-6 digits
Enter and Exit Program Mode
Set Mas1er Code
Add Common Users
- PIN/Card user ID: 0- 986;
- PIN length: 4-6 digits
Tips for PIN Security (Only valid for g digits PIN)
For higher security we allow you to hide your correct PIN with other numbers
up to a max of 9dlglts.
Example PIN 123434
You rould use “(123434)”” or””( 123434)
(‘•”can be any numbers !tom 0-9)
The device Connected with Fingerprint Reader
For example
Connect SF1 as the fingerprint reader to the device. two steps to enroll the
valid fingerprint.
- Add the Fingerprint (A) on SF1
- Add the same Fingerprint (A) on the device as below
NOTE: Fingerprint Adding in the APP is not valid for WiFi version.
Add Authorized User
- (User ID number is 987
- PIN length: 4~6 digits)
Remark
Authorized user can be card or PIN, read the Authorized Card or
lnpu1Authorlzed PIN, then all valid users can’t access; read the Authorized
Card or input Authorized PIN again, then all valid used can access again.
Add Panic Users
(User ID number Is 988-989; PIN length : 4-6 digits)
Add Visitor Users
- (User ID number is 990-999;
- PIN length: 4-6 digits)
Thera are 10 groups Visitor PIN/card available, the users can be specified up
to 10 times of usage, after a certain number of times,i. e. 5 times, the
PIN/card become invalid automatically.
Delete Users
Set Relay Configuration
The relay cofiguration sets the behaviour of the output relay on activation.
Set Access Mode
For Multi user access mode, the interval time of reading can not exceed 5
seconds, or else, the device will exit to standby automatically.
Set Strike-out Alarm
The strike-out alarm will engage after 1 O failed entry attempts (Factory is
OFF). It can be set lo deny access for 10 minutes after engaging or disengage
only after entering a valid card/PIN or Master code/card.
Set Door Open Detection
(Users will be suggested to connect a Door Contact on the device. Otherwise,
in the mobile APP. the door status will be shown ‘ON’ all the time. Or Connect
“D_IN’ and “GND”)
The function of Set Alarm Time also apply for anti-tamper ale rm.
Set Audible and Visual Response
Set Wiegand Format
Master Card Usage
Using Mastar Card to add and delete users
User Operation & Reset to Factory Default
- Open the door : Read valid user card or input valid user PIN
- Remove Alarm: Input Master Code # or read Master Card or valid user card / PIN or valid user card / PIN
- To reset to factory default & Add Master Cards: power off, press the Exit Button (or connect “OPEN” and “GND” to be short circuit), hold it and power on, there will be two beeps, then release the exit button (or disconnect “OPEN” and “ND”), the LED light turns into yellow, then read any 125KHz EM card or HID cards or 13.56MHz Mifare card, the LED will turn into red, means reset to factory default successfully. Of the card reading, it is the Master Card.
Remarks
- The type of the Master Card is according to the external reader. For example: t he external reader is 125kHz HID reader, then the Master Card must be 125KHz HID card.
- If no Master Card added, must press the Exit Button for at least 5 seconds before release. (This will make the previous registered Master Card invalid)
- Reset to factory default, the user’s information is still retained.
Advanced Application
Collection Card Mode
After this mode is turned on, all the cards can open the lock, at the same
time, all cards are added in the device.
User Information Transfer (Valid for Card/PIN Users) (Please note: only users added by the device can be transferred and valid for opening; users added by the mobile APP can also be transferred, but are unable to open the lock)
- The enrolled user can be transferred from a “Master “unit to a “Slave” unit.
- The Master code must be the same in the “Master” and the “Slave” unit.
Remarks
- The Master units and Slave units must be same series devices
- The Master Code of the Master unit and the Slave unit must be set to the same.
- If the Slave unit is already with the users enrolled, it will be covered after transferring.
- For full 986 users enrolled, the transfer takes about 30 seconds.
Set Transferring on Master Unit
Interlock
Let’s name the two devices as “A “and “B” for two doors “1” and “2”
- Step 1 : Enroll the users on Device A, then transfer the users’ information to Device B by “User Information Transfer” function
- Step 2 : Set both of the two devices (A and B) to Interlock function
If enable interlock, when and only door 2 is closed, the user can read the valid users on Reader A, door 1 will open; then when and only door 1 closed, read valid users on Reader B, door 2 will open.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>