Minka Lavery 2546-726 Baldwin Park 6 Light Coal and Soft Brass Chandelier Instruction Manual

: October 30, 2023
: MINKA LAVERY

Table of Contents

Minka Lavery 2546-726 Baldwin Park 6 Light Coal and Soft Brass Chandelier
Product Information
Product Usage Instructions
INSTALLATION INSTRUCTIONS
Hardware
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Minka Lavery 2546-726 Baldwin Park 6 Light Coal and Soft Brass Chandelier

Product Information

The product is a light fixture with item number 2546-726. The installation instructions are dated February 18, 2022. The fixture requires a power source and is designed to be mounted on a junction box. The fixture comes with a mounting plate, canopy, quick link, mounting screws, and three threaded rods of different lengths. It also requires six medium base T10 bulbs with a maximum wattage of 60 watts each or CFL or LED equivalent bulbs.

Product Usage Instructions

Turn off power at the fuse box or circuit breaker box.
Remove the old fixture and mounting hardware.
Unpack the new fixture and lay out all parts in a clean area.
Determine the desired hanging height and thread the rods (F1, F2, and F3) to all thread (I) of the fixture body. Screw loop (H1) onto rod (F1) and pass wires through each rod as you assemble.
Attach quick link (G) to loop (H1) and loop (H2) on the canopy (D). Carefully feed wire through loop (H1), quick link (G), and loop (H2).
Attach mounting plate (A) to the junction box with mounting screws (B). The side of the mounting plate (A) marked with GND and two convex points must face out.
Connect the electrical wires as shown in Fig. 2, making sure that all wire connectors are secured. If your junction box has a ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (A) using the green screw provided.
Slide canopy (D) over mounting plate (A) and secure with screws (E).
Install six medium base T10 bulbs (K) up to 60 watts each or CFL or LED equivalent bulbs in accordance with the fixture specification. Do not exceed the maximum wattage rating.
Place glass shade (L) over socket (J).
Return power to the junction box and test the fixture.

Note:
The illustration in Fig. 1 is for installation purposes only and may or may not be identical to the fixture purchased.

WARNING! SHUT THE POWER OFF AT THE FUSE OR CIRCUIT BREAKER.

INSTALLATION INSTRUCTIONS

PREPARATION (Fig.1 &Fig. 3)

Shut of power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.
Carefully unpack your new fixture and lay out all the parts in a clean area. Take care not to misplace any small parts necessary for installation.
Determine desired hanging height and thread rods (F1, F2 and F3) to all thread (I) of fixture body. Screw loop (H1) onto rod (F1). Carefully pass wires through each rod as you assemble.
Attach quick link (G) to loop (H1) and loop (H2) on the canopy (D). Carefully feed wire through loop (H1), quick link (G), and loop (H2).
Attach mounting plate (A) to junction box (not included) with mounting screws (B) (Size: #8-32N*L0.5”). The side of the mounting plate (A) marked with “GND” and two convex points must face out.
CONNECTING THE WIRES (Fig. 2)
Connect the electrical wires as shown in fig 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (A) using the green screw provided.
Tuck wire connectors neatly into the junction box.
COMPLETING THE INSTALLATION (Fig. 1)
Slide canopy (D) over mounting plate (A) and secure with screws (E).
Install (6) six medium base T10 bulbs (K) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification — DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).
Place glass shade (L) over socket (J).