MINKA LAVERY 2105-726 Townhall 4-Light Soft Brass and Coal Cage Pendant Light Instruction Manual

: October 30, 2023
: MINKA LAVERY

Table of Contents

MINKA LAVERY 2105-726 Townhall 4-Light Soft Brass and Coal Cage Pendant
Product Information
Product Usage Instructions
Installation Instructions
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MINKA LAVERY 2105-726 Townhall 4-Light Soft Brass and Coal Cage Pendant

Light

Product Information

The product is Item#2105-726, a new fixture for installation. It comes with a mounting plate, ground screw, junction box screw, rod, candle cover, and acrylic ball. The fixture wires are black or smooth, white or ribbed, and bare copper for ground. The house wires are black for hot, white for neutral, and green for ground. The installation manual also includes hardware bags A and B with additional parts such as a canopy, mounting screw, lock-up knob, quick link, and loop.

Product Usage Instructions

Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.
Unpack the new fixture and lay out all the parts.
Refer to Fig. 1 for the preparation steps which include attaching the mounting plate, ground screw, and junction box screw.
Refer to Fig. 2 for the fixture wires and house wires color codes and connect them accordingly.
Refer to Fig. 3 for the additional hardware parts and attach them as required.
Once all the parts are attached, turn on the power and test the fixture.

Note: The illustration in Fig. 1 is for installation purposes only and may or may not be identical to the fixture purchased.

READ AND SAVE THESE INSTRUCTIONS

WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.

Installation Instructions

PREPARATION

Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.
Carefully unpack your new fixture and lay out all the parts in a clean area. Take care not to misplace any small parts necessary for installation.
- ASSEMBLING THE FIXTURE WITH CHAIN LOOP (Fig. 1 &Fig. 3)
Place square tubes (L) on metal frame (N) and attach with countersunk screws (M) (Size: 8#-32N*L0.3”).
Align top frame (H) with square tubes (L) and attach with screws (T) (Size: 8#-32N*L0.3”) and cover the hole with plastic plug (S).
Screw metal tube (J) onto the all thread on light cluster (K).
Attach center rod (I) onto all thread on metal tube (J).
Thread center rod (I) into the all thread on top frame (H).
Place acrylic ball (Q) to bottom of fixture body (K) and secure with allen screw (O) using wrench (P) provided.
Determine the desired hanging height and thread rods (G1, G2) to the all thread of top frame (H). Then attach loop (F1) by screwing onto rod (G1). Pass the wires carefully through each rod as you assembled.
Attach quick link (E) connect to loop (F1) and loop (F2) on canopy (C), carefully feed the wire through loop (F1), quick link (E) and loop (F2).
Attach mounting plate (A) to the junction box (not included) with junction box screws (B) (Size: #8-32N*L1”). The side of the mounting plate (A) with “GND” marked on it and two convex points must face out.
The support cable is provided to support weight of fixture while wiring. Align fixture to mounting plate (A) and attach hook (W) on the end of support cable (V) into a slot located on mounting plate (A). Carefully allow support cable (V) to support weight of fixture while wiring (Fig.1 Fig3).
- CONNECTING THE WIRES (Fig. 2)
Connect the electrical wires as shown in fig.2, making sure that all wire connectors are secured. If junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (A) using the green screw provided.
Tuck the wire connectors neatly into the junction box.
- COMPLETING THE INSTALLATION (Fig. 1)
Slide canopy (C) over mounting screws (U) attached to mounting plate (A) and secure with knobs (D).
Install (4) four candelabra base bulbs up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification—DO NOT EXCEED THE MAXIMUM WATTAGE RATING!