MULTIPLEX 10122022 Fresh Blender Water Filter Retrofit Wall Instructions

MULTIPLEX 10122022 Fresh Blender Water Filter Retrofit Wall

Product Information

The FreshBlender Water Filtration Retrofit Wall Mount is a water filtration kit that can be mounted to a wall and is compatible with all Multiplex FreshBlender units. The kit includes a wall mount filter assembly, pre-filter, 10000-P filter, clamps, elbows, fittings, tubing, and a filter manual. It is important to note that the wall mount water filter system should not block air flow to any machines and should not come in contact with any machines. The system needs to be easily accessible for staff to change the water filter cartridges.

Product Usage Instructions

1. Review the literature packet included with parts and filters.
2. Power off the machine using the power switch on the top right of the unit and unplug it.
3. Carefully move the machine away from the wall without damaging water or drain lines.
4. Place a bucket under the rear drain.
5. Turn off the water shutoff valve and disconnect the water line from the back of the machine.
6. Verify that the o-ring on the male quick connect at the end of the current water supply line is not damaged. If it is damaged, replace it and coat it with food-grade lubricant.
7. Locate the new water filter system assembly and tighten the four nuts located behind the gauges with a 3/8 wrench.
8. Tighten the four screws on both of the filter brackets located around the gauges.
9. Verify that the gauges are secured by pressing each one into corresponding fitting.
10. Mount the bracket to the wall using the correct hardware in each of the six bracket mounting holes. Position the water filter assembly to prevent the bracket with filters installed from interfering with air flow of any machines and verify that the water filter assembly and filters do not come in contact with any machines.
11. Use a permanent marker to write the install date on each filter.
12. Lubricate the o-rings with food-grade lubricant.
13. Carefully insert the pre-filter in the left assembly slot and the filter in the right assembly slot.
14. Assemble the tubing for the incoming water from the current water source to the filter system. Cut the tubing length to have enough length from current water supply line to water filter system water inlet.

It is important to note that before starting any installation, power off the machine and unplug it from the power source. The unit contains sharp moving parts, and gloves should be worn to protect hands. Additionally, keep the refrigeration cabinet door closed so that the product remains chilled while the unit is off.

This water filtration kit mounts to a wall. Do NOT mount this kit to a unit.

Important

• Wall mount water filter system should not block air flow to any machines and should not come in contact with any machines.
• Wall mount water filter system needs to be easily accessible for staff to change the water filter cartridges.

TOOLS REQUIRED

• Puncture resistant Gloves
• Clean Bucket
• Clean Towels
• Drill
• Universal Screw Driver
• Tubing Cutters
• 3/8” Wrench
• Food Grade Lubricant
• Tools to mount bracket to permanent location surface PARTS REQUIRED
• Mounting hardware for permanent location surface
• In-line Water Shutoff Valve
• 020009252 Water Filtration Kit (Parts listed below)

FOR 3/8” TUBE ID

| WBL-96-069
1| CPLNG LC FEM VLVD INLINE 3/8 BARB| 3547347
1| CPLNG LC MAL VLVD INLINE 3/8 BARB| MCP00246
1| O-RING NSF #71112 FOR MCP00246|
4| FITTING CLIPS, RED| WBL-96-058
20’ (6m)| TUBING, 3/8”ID X 19/32” OD, BRAIDED, PVC| 02-0584
1| FILTER MANUAL| 000016341
1| INSTRUCTION| 020009254

Warning: Power OFF the machine and unplug from power source, this unit contains sharp moving parts. Wear gloves to protect hands.
Important: Keep refrigeration cabinet door closed so product remains chilled while unit is off.

PREPARATION

1. Review literature packet included with parts and filters.

2. Power unit OFF using power switch on top right of unit and unplug.

3. Without damaging water or drain lines, carefully move machine away from wall.

4. Place bucket under rear drain.

5. Turn off water shutoff valve and disconnect water line from back of machine.

6. Verify o-ring on MALE QUICK CONNECT at end of current water supply line is not damaged. If o-ring is damaged, replace and coat with food-grade lubricant. INSTALLATION

7. Locate new water filter system assembly. Tighten the four (4) nuts located behind the gauges with 3/8” wrench.

8. Tighten the four (4) screws on both of the filter brackets located around the gauges.

9. Verify gauges are secured by pressing each one into corresponding fitting. MOUNT BaRACKET

10. Mount bracket to wall using correct hardware in each of the six (6) bracket mounting holes.
    A. Position water filter assembly to prevent bracket with filters installed from interfering with air flow of any machines.
    B. Verify water filter assembly and filters do not come in contact with any machines.

11. Mount bracket to wall using correct hardware in each of the six (6) bracket mounting holes. A. Position water filter assembly to prevent bracket with filters installed from interfering with air flow of any machines.
    B. Verify water filter assembly and filters do not come in contact with any machines.

12. Lubricate o-rings with food grade lubricant.

13. Carefully insert the Pre-filter in the left assembly slot. Carefully insert the Filter in the right assembly slot. INCOMING WATER LINE EXTENSION WITH SHUTOFF

14. Assemble the tubing for the incoming water from the current water source to the filter system.

    • A. Cut tubing length to have enough length from current water supply line to water filter system water inlet.
    • B. Install in-line water shutoff valve close to water filter system end of tubing .
    • C. Install 3/8” BARB TO STEM FITTING to water filter system end of tubing using correct size Oetiker clamp.
    • D. Install 3/8” STEM ELBOW FITTING onto the stem of the 3/8” BARB TO STEM FITTING. SECURE WITH RED CLIP.
    • E. Install FEMALE QUICK CONNECT to end of tubing that will connect to current water source MALE QUICK CONNECT using correct size Oetiker clamp. FILTERED WATER LINE TO UNIT

15. Assemble the tubing for the filtered water from the water filter system to the rear of the machine.

16. A. Cut tubing necessary to have enough length from the water filter system to the machine with 6’
    (1.8m) additional tubing to allow for machine to be pulled away from wall for servicing.

17. B. Install 3/8” BARB TO STEM FITTING to water filter system end of tubing using correct size Oetiker clamp.

18. C. Install 3/8” STEM ELBOW FITTING onto the stem of the 3/8” BARB TO STEM FITTING. SECURE WITH RED CLIP.

19. D. Install MALE QUICK CONNECT to end of tubing that will connect to rear of machine using correct size Oetiker clamp. CONNECTIONS

20. Connect water inlet line to left water line of assembly.

21. Turn OFF in-line water shutoff valve.

22. Connect MALE quick-connect of the current incoming water supply line to new FEMALE quick-connect of the WATER LINE EXTENSION with in-line water shutoff.

23. Connect FILTERED WATER LINE to RIGHT side of water filter assembly.

24. Turn ON in-line water shutoff valve. Inspect tubing and new water filter system for leaks. Fix leaks if necessary.

25. Hold water line from right of assembly over bucket and flush water line by pressing open quick connect. Flush at least two (2) gallons of water through filter before use (approximately 1 minute of flushing). Water may run cloudy due to air however will clear quickly. Refer to filter manual for more information.

26. Connect right water line of assembly to machine. REASSEMBLY

27. Move machine back in place.

28. Verify drain is connected correctly.

29. Plug unit to power source and power ON.
    VERIFY OPERATION

30. Enter the Service Menu.

    • E. Menu screens are hidden and will require a password. From start screen, touch the three corners in the order shown to access the password screen.
    • F. Enter password for SERVICE MENU and then press ENTER.

31. Empty water from system.

    • G. Press SERVICE OUTPUT.
    • H. Press DISPENSE & BLEND.
    • I. Toggle WATER DISPENSE option to ON.
    • J. Water will dispense into dispense area.
    • K. Screen will time out and return to previous screen.
    • L. Press BACK or LOGOUT until return to main screen.

32. Make several drinks with manager present to confirm operation.

NOTE: For best results, perform ICE BIN DUMP to remove old, unfiltered ice. Perform 3-corner touch, go to SERVICE MENU/SERVICE OUTPUTS/ICE BIN DUMP and follow onscreen instructions.
For units that have been installed for over a year, to achieve maximum benefits of new water filtration system it is recommended to perform FreshBlender Annual Tune Up including descale with ice maker component disassembly.

Document Number: 020009254 October 27, 2022

MULTIPLEX
address: 645 PARK EAST BLVD SUITE 5, NEW ALBANY, IN 47150 800-689-0157 OR 844-724-CARE
WWW.MULTIPLEXBEVERAGE.COM

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>