MULTIPLEX FreshBlender Decal Installation Guide

: October 30, 2023
: MULTIPLEX

Table of Contents

TOOLS REQUIRED
PARTS REQUIRED
TECHNICAL SUPPORT
CUSTOMER SUPPORT
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MULTIPLEX FreshBlender Decal

MULTIPLEX FreshBlender Decal

TOOLS REQUIRED

Scissors
Hand Decal Applicator/Smoothing Tool
Clean Cloths, low-lint
Isopropyl Alcohol (70-90%)

PARTS REQUIRED

Decals

NOTE: Contact Multiplex Technical Support for part numbers.

TECHNICAL SUPPORT

Country	Tech Support Phone Number
AUSTRALIA	1800-423-626
CANADA	1-844-724-2273
USA	1-844-724-2273

Warning
Power unit OFF and unplug from power source to prevent electrical shock.

If decals are rolled up, lay decal on a flat surface to remove curling.
Power unit OFF and unplug, then unlock door.
Remove left and right side panels if replacing decals on side panels.
NOTE: Front top door must be open to remove right-side panel.
SIDE PANEL DECAL
Lay side panel on flat surface with clips and curve hanging over edges so panel is flat.
Peel 2-3 inches (5-8cm) of old decal back along one edge.
Using scissors cut 2-3 inch (5-8cm) slits 6 inches (15cm) apart along loose edge.
Using scissors cut 2-3 inch (5-8cm) slits 6 inches (15cm) apart along loose edge.
Continue peeling old decal off in strips.
Spray panel surface with isopropyl alcohol , scrub surface with clean cloth to remove dirt or adhesive residue.
Dry thoroughly with a different clean cloth. Make sure surface is dry and dirt/lint free.
Lay new decal face-up over clean panel and peel back 4- inches (10-13cm) along top edge. Do not take back of new decal off at this time.
NOTE: Curved edge is top of panel. Top of decal should be oriented along top of panel.
Locate two (2) alignment marks on new decal.
Align two (2) decal alignment marks with the two (2) clips located toward top of panel.
NOTE: Do NOT align top of decal with top edge of panel, use alignment marks.
Using clean hands start at center of decal and gently press outwards to secure the exposed adhesive back of decal to panel.
Use decal applicator/smoothing tool to press out bubbles along top edge of decal to firmly secure exposed adhesive to panel.
With one hand remove remaining backing while guiding the decal onto the panel with other hand.
With one hand remove remaining backing while guiding the decal onto the panel with other hand.
Repeat process for other panel if necessary.
Reinstall both panels.
Close and lock upper front door.
Plug in unit and power ON.
Verify drain is correctly connected.
REFRIGERATED CABINET DOOR DECAL
Peel 2-3 inches (5-8cm) of old decal back along one edge.
Using scissors cut 2-3 inch (5-8cm) slits 6 inches (15cm) apart along loose edge.
Starting at edge with slits, peel away old decal in strips.
Spray panel surface with isopropyl alcohol , scrub surface with clean cloth to remove dirt or adhesive residue.
Dry thoroughly with a different clean cloth. Make sure surface is dry and dirt/lint free.
Lay new decal face-up on clean surface and peel back 4- inches (10-13cm) along top edge. Do not take back of new decal off at this time.
Center and align top of new decal with refrigerated cabinet door.
Using clean hands start at center of decal and gently press outwards to secure the exposed adhesive back of decal to panel.
Use decal applicator/smoothing tool to press out bubbles along top edge of decal to firmly secure exposed adhesive to panel.
With one hand remove remaining backing while guiding the decal onto the panel with other hand.
Starting at the top of the decal use decal applicator tool to press bubbles out of decal using short strokes moving down towards floor.

CONFIRM OPERATION
Verify drain is correctly connected.
Make several drinks with manager present to confirm operation.