BORMANN PRO BBS1210 Airless Paint Sprayer User Manual

BORMANN PRO BBS1210 Airless Paint Sprayer

Product Information

The BBS1210 034353 is a scroll saw designed for cutting wood, plastic, and metal. It has a voltage/frequency of 230V, 50Hz, and a power of 90W. The maximum cutting width is 406mm, and the maximum cutting depth is 50mm. It has a blade speed of 550-1600spm and a flexible shaft speed of 1650-4800RPM. The table adjustment can be set from 0-45 degrees. The product comes with an LED light, height adjuster, guard, upper blade holder, hold down foot, mitre fence, ON/OFF switch, footswitch, dust extraction outlet (35mm Dia.), flexible drive, blade storage, air blower, and blade tension regulator.

Usage Instructions

1. Read the manual thoroughly before using the product.
2. Ensure that all repair, inspection, maintenance, and replacement work is carried out by technicians of the authorized service department of the manufacturer to ensure safety and warranty validity.
3. Always use the product with the supplied equipment to avoid malfunctions or serious injury. The manufacturer and importer will not be liable for injuries or damages resulting from the use of non-conforming equipment.
4. Before using the product, wear eye protection, a dust mask, and ear protection to avoid injury.
5. Assemble the product by attaching the air pipe to the top of the bellows, attaching the air pipe to the metal tube, fixing the metal tube in place with the nozzle pointing down to the middle using a phillips screw, attaching the hold down foot using a screw making sure it is parallel to the table, and attaching the transparent guard using a screw, washer, and nut.
6. Fit the two batteries provided for the LED light, ensuring they are the correct way around. Replace the cover and refit the screws.
7. Store spare blades in the storage box on the left-hand side of the scroll saw.
8. Only attach the flexible shaft when you intend to use it. When not in use, leave the plastic threaded cover in place.

The manufacturer reserves the right to make minor changes to product design and technical specifications without prior notice unless these changes significantly affect the performance and safety of the products. The parts described / illustrated in the pages of the manual that you hold in your hands may also concern other models of the manufacturer’s product line with similar features and may not be included in the product you just acquired.

• To ensure the safety and reliability of the product and the warranty validity, all repair, inspection, repair or replacement work, including maintenance and special adjustments, must only be carried out by technicians of the authorized service department of the manufacturer.
• Always use the product with the supplied equipment. Operation of the product with non-provided equipment may cause malfunctions or even serious injury or death. The manufacturer and the importer shall not be liable for injuries and damages resulting from the use of non-conforming equipment.

Safety Instructions

WARNING:
Do not attempt to operate the machine until you have read thoroughly and understood completely all instructions, rules, etc. contained in this manual. Failure to comply may result in accidents involving fire, electric shock, or serious personal injury. Keep this owner’s manual and review frequently for continuous safe operation.

1. Know your machine. For your own safety, read the owner’s manual carefully. Learn its application and limitations, as well as specific potential hazards per-tinent to this machine.
2. Make sure all tools are properly earthed.
3. Keep guards in place and in working order. If a guard must be removed for maintenance or cleaning, make sure it is properly replaced before using the machine again.
4. Remove adjusting keys and spanners. Form a habit of checking to see that the keys and adjusting spanners are removed from the machine before switched it on.
5. Keep your work area clean. Cluttered areas and workbenches increase the chance of an accident.
6. Do not use in dangerous environments. Do not use power tools in damp or wet locations, or expose them to rain. Keep work areas well illuminated.
7. Keep children away. All visitors should be kept a safe distance from the work area.
8. Make workshop childproof. Use padlocks, master switches and remove starter keys.
9. Do not force the machine. It will do the job better and be safer at the rate for which it is designed.
10. Use the right tools. Do not force the machine or attachments to do a job for which they are not designed. Contact the manufacturer or distributor if there is any question about the machine’s suitability for a particular task.
11. Wear proper apparel. Avoid loose clothing, gloves, ties, rings, bracelets, and jewellery which could get caught in moving parts. Non-slip footwear is recom-mended. Wear protective hair covering to contain long hair.
12. Always use safety glasses. Normal spectacles only have impact-resistant lenses. They are not safety glasses.
13. Do not over-reach. Keep proper footing and balance at all times.
14. Maintain the machine in good condition. Keep the machine clean for best and safest performance. Follow instructions for lubrication and changing accessories.
15. Disconnect the machine from power source before servicing and when changing the blade.
16. Never leave the machine running unattended. Turn the power off. Do not leave the machine until it comes to a complete stop.
17. Do not use any power tools while under the effects of drugs, alcohol or medication.
18. Always wear a face or dust mask if operation creates a lot of dust and/or chips. Always operate the tool in a well ventilated area and provide for proper dust removal. Use a suitable dust extractor.
    • Risk of Injury: Never Reach Into A moving Part
    • Always Wear Eye Protection
    • Always Wear A Dust Mask
    • Always Wear Ear Protection

Technical Data

Flexible shaft: 1650 ~ 4800RPM

Table adjustment:| 0-45o

Description of main parts

1. LED Light
2. Height adjuster
3. Guard
4. Upper Blade holder
5. Hold down foot
6. Mitre fence
7. ON/OFF switch
8. Footswitch
9. Dust Extraction Outlet 35mm Dia.
10. Flexible Drive
11. Blade Storage
12. Air Blower
13. Blade Tension regulator

Assembly instructions

Attach the air pipe to the top of the bellows.

Attach the air pipe to the metal tube.

Fix the metal tube in place, with the nozzle pointing down to the middle, using the phillips screw.

CAUTION!
DO NOT OVER-TIGHTEN AS THIS CAN CRUSH THE PIPE

Attach the hold down foot using the screw making sure it is parallel to the table.

Attach the transparent guard using the screw, washer and nut.

Undo the three small screws on the light cover and put in a safe place.

Fit the two batteries provided ensuring they are the correct way around. Replace the cover and refit the screws.

Put your spare blades in the storage box on the left hand side of the scroll saw.

ONLY ATTACH THE FLEXIBLE SHAFT WHEN YOU INTEND TO USE IT. WHEN NOT IN USE LEAVE THE PLASTIC THREADED COVER IN PLACE.

• To use the flexible drive, firstly remove the cover.

Locate the power take off. Insert the drive shaft into the hole and then screw the outer cap onto the outlet by hand.

THE FLEXIBLE SHAFT ONLY NEEDS TO BE HAND TIGHTENED.

It is normal for scroll saws to create a lot of vibration. Fixing the saw down to a heavy duty work bench is recommended. Some people also find using a vibration absorbing mat helps.

• There are three bench mounting point provided.

There are two types of blade that can be used with this scroll saw. When fitting a blade, always ensure the teeth of the blade are point-ing down and facing towards the direction of feed.

• Plain End Type Blade
• Pin End Type Blade

Using pin end blades
The pin type blade simply hooks over the upper and lower blade holder. Make sure the pins sit in the indentation. Pin type blades are quick and easy to change, but are not available in very narrow widths for making the most intricate cuts.

To Fit the blade:
Remove the table insert by pressing upwards from underneath the table

Turn the blade tension knob counterclockwise to decrease it.

Hook the lower pin over the lower blade holder. Press down lightly on the upper blade holder and hook the upper pin over the upper blade holder. Replace the table insert and lower the blade tension lever. To remove the blade, follow these instructions in reverse.

Alternate fitting:
The pin type blade can also be used in the sideways position as shown. Feed direction will be right to left. This option allows cuts to be made in materials longer than 400mm (16”) in length.

Using plain end blades

• To set the blade clamps onto plain end blades, use the setting jig located on the top arm.
• Loosen the grub screws on either side of the clamps then slot a new blade into each end.
• Tighten up the grub screws to hold the blade in place making sure it is held centrally.

Take off the blade tension. Hook the blade clamp onto the lower blade holder (may be easier using a hand under the table). Once the lower clamp is in place, press down the top arm so that you can hook the top holder into place. Refit the table insert plate. Follow the blade tensioning instructions as for Pin End blades.

Operating Instructions

A suitable dust extractor should always be used.

There are two ways to control the scroll saw:

• The control panel or The foot switch

To use the control panel:

• Set the red rocker switch to position labelled ‘I’
• Press the green ‘On’ button labelled ‘I’
• The red light will illuminate and saw will start.
• Set the desired speed by turning the speed dial.
• Clockwise to increase the speed and anti-clockwise to decrease the speed.

To use the foot switch:

• Set the red rocker switch to position labelled ‘0’
• Press the green ‘On’ button labelled ‘I’
• The red light will illuminate but the saw will not start.

To start the saw, press down on the foot switch. The blade will move at the set speed. Using the foot switch allows both hands to be used to guide the work piece and the convenience of stopping and starting without taking your hands off.

The speed can be changed at any time by turning the speed dial. Clockwise to increase the speed and anti-clockwise to decrease.

The scroll saw is fitted with a battery powered light which can be turned on using the switch on the top.

The light is on a flexible arm and can be adjusted so that it shines onto the work piece.

Regular Cutting
Lower the hold down foot so that it is just above the height of the wood to be cut. It prevents the work piece lifting off the table dur-ing the upstroke of the blade. Adjust the air blower so that it is pointing down at the cutting area. This enables a clearer view of the cut, particularly useful when fol- lowing pencil lines.

Bevel Cutting
To adjust the angle of the work table slacken off the knob.

Tilt the table to the desired angle and tighten the locking knob.

Mitre Cutting
A mitre guide is provided to allow straight cuts on small pieces of timber.

The mitre guide can be set up to a 45 degree angle for performing mitre cuts.

With the Pin type blade set in the sideways position the mitre guide can be used in the rear table slot.

Using the Flexible Shaft
When using the Flexible shaft ensure the blade guard on the scroll saw is fully down

• the blade will still be moving.

To fit a tool into the flexible shaft:

• Insert the spindle lock tool into the hole in the outer case of the spindle to stop the spindle rotating.
• Put the chosen tool into the collet.
• Use the spanner to tighten the collet.

Caution: DO NOT OVER-TIGHTEN

• Various flexible drive accessories are supplied for sanding, polishing, grind-ing and shaping operations.
• They can be used on wood, metal and plastics.

ALWAYS REMOVE THE FLEXIBLE SHAFT FROM THE SCROLL SAW WHEN NOT IN USE

Cleaning, maintenance and Storage

Warning!
Prior to any adjustment, maintenance or service work disconnect the mains power plug!Wipe chips and dust off the machine from time to time using a cloth. When cleaning the plastic do not use corrosive products.

Cleaning

• Keep all safety devices, air vents and the motor housing free of dirt and dust as far as possible. Wipe the equipment with a clean cloth or blow it with com-pressed air at low pressure.
• We recommend that you clean the device immediately each time you have finished using it.
• Clean the equipment regularly with a moist cloth and some mild soap. Do not use cleaning agents or solvents; these could attack the plastic parts of the equipment. Ensure that no water can seep into the device. The ingress of water into an electric tool i creases the risk of an electric shock.

Maintenance
There are no parts inside the equipment which require additional maintenance.

Storage
Store the device and its accessories in a dark, dry and frost proof place that is inaccessible to children. The optimum storage temperature is between 5 and 30˚C. Cover the electrical tool in order to protect it from dust and moisture. Store the operating manual with the electrical tool.

Disposal and recycling

The equipment is supplied in packaging to protect it from being damaged in transit. The raw materials in this packaging can be reused or recycled. The equip-ment and its accessories are made of various types of material, such as metal and plastic. Defective components must be disposed of as special waste. Ask your dealer or your local council.

WWW.NIKOLAOUTOOLS.GR.

WARRANTY

The power tools have been manufactured according to strict standards, set by our company, which are aligned with the respective European quality standards. The power tools of our company are provided with a warranty period of 24 months for non-professional use, 12 months for professional use and 6 months for batteries. The warranty is valid from the date of purchase of the product. Proof of the warranty right is the purchase document of the tool (retail receipt or invoice). Under no circumstances shall the company cover the relevant cost of spare parts and respective required working hours unless a copy of the purchase document is presented. In case the repair has to be done by our service department the cost of transpor-tation (to and from) is entirely borne by the sender (client). The tools must be sent for repair to the company or to an authorized workshop in the appropriate way and means of transport.

WARRANTY EXEMPTIONS AND RESTRICTIONS:

1. Spare parts that wear out naturally as a consequence of being used (brushes, cables, switches, chargers, chokes etc.).
2. Tools damaged as a result of non-compliance with the instructions of the manufacturer.
3. Tools poorly maintained.
4. Use of improper lubricants or accessories.
5. Tools given to third entities free of charge.
6. Damage due to an electrical connection at a voltage other than that indicated on the appliance plate.
7. Connection to a non-earthed power supply.
8. Change in current voltage.
9. Damage resulting from the use of salty water (e.g., washing machines, pumps).
10. Damage or malfunction resulting from improper cleaning procedure of the tool.
11. Contact of the tool with chemicals, or damage as a result of moisture or corrosion.
12. Tools that have been modifi ed or opened by unauthorized personnel.
13. Tools used for rent.

The warranty covers only the free of charge replacement of the component that presents a manufacturing defect or material failure. In case of lack of a specifi c spare part the company reserves the right to replace the tool with another corresponding model. After all warranty procedures have been concluded, the warranty period of the tool shall not be extended or renewed. Replacement of a spare part with repair charge is covered by a 1 year warranty of good operation, subject to compliance with the warranty terms. The spare parts or tools that are replaced remain in the possession of our company. Requirements, other than those mentioned in this warranty form, regarding power tools repair or damage thereof, do not apply. Greek law and relative regulations apply to this warranty.

This appliance is a quality product. It was designed in compliance with current technical standards and made carefully using normal, good quality materials. The warranty period is 24 months for non-professional use and 12 months for professional use and commences on the date of purchase, which can be verifi ed by the receipt, invoice or delivery note. During this warranty period all functional errors, which, despite the careful treatment described in our operating manual, are verifi ably due to material flaws, will be rectified by our after-sales service staff .

The warranty takes the form that defective parts will be repaired or replaced with perfect parts free of charge at our discretion. Replaced parts will become our property. Repair work or the replacement of individual parts will not extend the warranty period not will it result in a new warranty period be- ing commenced for the appliance. No separate warranty period will commence for spare parts that may be ted. We cannot off er a warranty for damage and defects on appliances or their parts caused by the use of excessive force, im-proper treatment and servicing. This also applies for failures to comply with the operating manual and the installation or spare and accessory parts that are not included in our range of products.

In the event of interference with of modifications to the appliance by unauthorized persons, the warranty will be rendered void. Damages that are attributable to improper handling, over loading, or nat-ural wear and tear are excluded from the guarantee. Damages caused by the manufacturer or by a material defect will be corrected at no charge by repair or by providing spare parts. The prerequisite is that the equipment is handed over assembled, and complete with the proof of sale and guarantee. For a guar-antee claim, only use the original packaging. That way, we can guarantee quick and smooth guarantee processing. Please send us the appliances post-paid or request a Freeway sticker. Unfortunately we will be unable to accept appliances that are not postpaid. The warranty does not cover parts that are subject to nat-ural wear and tear. If you wish to make a warranty claim, report faults or order spare parts or accessories, please contact the after-sales center: Subject to change without prior notice.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>