ACOPOWER 100w 12v Monocrystalline Solar Panel Module User Manual
- May 15, 2024
- ACOPOWER
Table of Contents
ACOPOWER 100w 12v Monocrystalline Solar Panel Module
Application Scope
- Courtyard lighting.
- Small household lighting system.
- Street lighting.
- Portable solar power.
- All small power electrical devices & small PV
Electrical Characteristics
- Characteristics: 100W
- Open-Circuit Voltage(Voc): 22.9V
- Optimum Circuit Voltage(Vmp): 19.4 V
- Short-Circuit Current(Isc): 5.5A
- Optimum Circuit Current(Imp): 5.2A
- Maximum Power at STC(Pmax): 100W
- Cell Efficiency: 22%
- Operating Temperature: -40 C to +85 C
- Maximum System Voltage: 1000V DC
- Power tolerance: ±3%
- STC: Irradiance 1000W/m², Module temperature 25 C, AM=1.5
Mechanical Characteristics
- Type of cell: Mono-crystalline 166 x166 mn (6.5 inches)
- Dimensions: 1070 x 535 x 35mm (42.1 x 21.1 x 1.4 inches)
- Weight: 6.0kg(13.2lb)
- Front Glass: Low-Iron Tempered Glass
- Frame: Aluminum Alloy
- Encapsulation: Glass/EVA/Cells/EVA/TPT
- Relative Humidity: 0 to 100%
- Resistance: 227g steel ball fall down from 1m height and 60m/s wind
- Snow load parameters: 2400Pa
Size
Temperature Coefficients
- Nominal Operating Cell Temperature(NOCT): 45 C ±5 C
- Temperature Coefficient of Pmax: -0.45%/C
- Temperature Coefficient of Voc: -0.35%/C
- Temperature Coefficient of Isc: +0.05%/ C
- Maximum SeriesFuse/current rating: 10A
General provision
a. Installation should only be performed by qualified personnel. Each
module is supplied with connectors used for system electrical connections. For
the convenience of installation, ACOPOWER can provide customized cables as
client required. Installers should assume all risks of injury that might occur
during installation.
b. Inappropriate transport and installation may break the module and void
the warranty.
Ready to work
To set up the mounting bracket of solar panel depends on its size. The bracket fixting hole must be on the basis of the pitch of hole of the solar panel module. The installation tools include: appropriate fasteners (Rails Clamp Hardware screws, nuts) and the other installation tools.
Installation Photovoltaic Module
Grounding installation:
a. For column installation, U-shaped triangle support is adopted. 4
angles (30° 35° 40° 45°) can be adjusted according to the position of the
hole.
b. For simple installation, please use facile fixative bracket to set up.
It is easy to adjust the angle. This installation can be set up on the floor
or the wall.
c. For rooftop installation, please choose “Solar Panel Mounting Z
Bracket “to Install on the roof and RV, Boats and other systems
Solar panel connection
The length of the cable that connected with the solar panel junction box is 1M (39.37 INCH), which should be noted the polarity of the output. The standard wiring polarity is “face terminal box: left” – “right” + “, also the polarity can be viewed on the wiring. After installation of each solar panel, series and parallel connection must be set up based on design requirements of voltage and current. Series connection is “-” and “+”, “-” and “+” operator increased the charging voltage, FIG:(a). Parallel connection is “-” and “-” connected, “+” and “+” increased the charging current, FIG:(b). To use a different connection, solar panel can charge battery for 12V, 24V 36V 48V through the solar charge controller
The installation angle can be adjustable according to different geographical location, mostly associated with latitude.
ACOPOWER Team has solar design experts can provide professional and free design! Email: tech@acosolar.com
Customer Support
Power Your Green Life!
USA Sales: 4120 Valley Blvd, Walnut, CA 91789, USA
Tel: +1-626-575 7722
Fax: +1-626-737 1140
Email: sales@acopower.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>