intezze TRIQ+ True Wireless Earbuds Instruction Manual

intezze TRIQ+ True Wireless Earbuds

Switching the earphones ON/OFF

Before you begin using the earphones, remove the protective film from the charging pins. After removing the earphones from the charging case, the earphones start automatically, switch to pairing mode, and the LEDs on both earphones begin to flash quickly. You can now pair the earphones with your phone. After successful pairing, you will hear “Connected” from the earphones. After pairing, the earphones automatically connect to the phone the next time you use them. The earphones can also be turned on manually by pressing the multi-function button on both earphones for three seconds. When you put the earphones back in the case, they turn off automatically. (The case LED lights up for four seconds and then goes out). The earphones can also be switched off manually. It is necessary to unpair them from the phone first and then hold the multi-function buttons on both earphones for four seconds. The earphones turn off automatically if they are not paired with the phone or if they are out of Bluetooth range.

Earphone function – touch gestures

• Adjust volume: + Increase: Single tap the R earphone – Decrease: Single tap the L earphone
• Answering a call: When a call is incoming, single tap the L or R earphone
• Ending a call: Double tap the L or R earphone
• Rejecting a call: When a call is incoming, hold the L or R earphone for two seconds
• Play/Pause: Double tap the L or R earphone
• Next track: Hold the R earphone for two seconds
• Previous track: Hold the L earphone for two seconds
• Game/Music: sound modes Triple tap the L or R earphone

Reset function

When to use it? E.g. after an unsuccessful connection to the phone or when only one earphone is playing. However, it can help in many other situations.

1. Delete “lntezze TRIQ+” from the list of paired devices on the phone. Ideally, turn off the Bluetooth function on your phone as well.
2.  Remove both charged earphones from the case. The LEDs on both earphones start flashing white and you will hear “Pairing” from the earphones.
3. Quickly tap the multifunction button on both earphones five times. “Power OFF” is heard and the earphones turn off. By holding down both multifunction buttons for three seconds, the earphones will turn on again and “Power ON” will be heard. The LEDs on the earphones will alternately flash red and blue.
4. Place the earphones next to each other so that you can see them. The LEDs on both earphones start flashing white after about 8–10 seconds and you will hear “Pairing” from the earphones. This completes the reset successfully and the earphones can be paired with the phone again.

Warranty conditions – The warranty does not cover the following

situations:

1. Damage caused by unauthorised tampering with the device.
2. Filters clogged by earwax (may not be immediately visible) or otherwise needing cleaning. Cleaning must be done by an authorised service and a fee is charged.
3. Earbuds with their duct filters removed.
4.  Physical damage to the earbuds caused by a fall or impact.
5.  Damage caused by force majeure.

Caution

1. To enable connection of the charging pins, you must first remove the protective film from the pins on the earbuds.

2.  Fully charge the case together with the earbuds prior to first use.

3.  If you are not using the earbuds for an extended time, keep charging the earbuds and case regularly, to avoid damaging the batteries (shortening their lifespan).

4.  Keep the volume at the lowest possible level. Listening at loud volumes for an extended time may damage your hearing irreversibly!

5.  Children must be supervised by an adult when using the earbuds. Risk of swallowing small parts.

6.  Clean using a slightly damp cloth only.
   Do not use the earbuds outside their supported temperature range of -15°C to

7. + 50°C.

8. Do not charge the case or earbuds in places with a temperature below 0°C.

9.  Do not expose the earbuds or case to direct sunlight for extended periods.

10.  Never disassemble or otherwise try to repair the earbuds.

11. Keep the mesh on both earbuds clean to avoid sound quality degradation.

12. Using the headphones in a dusty or humid environment can damage them.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>