TELTONIKA Networks RUT360 LTE Industrial Router User Guide

TELTONIKA Networks RUT360 LTE Industrial Router

Overview

POWER SOCKET PINOUT

HARDWARE INSTALLATION

1.  Push the SIM holder button with the SIM needle.
2.  Pull out the SIM holder.
3. Insert your SIM card into the SIM holder.
4.  Slide the SIM holder back into the router.
5. Attach Mobile and WiFi antennas.
6.  Connect the power adapter to the socket on the front of the device. Then plug the other end of the power adapter into a power outlet.
7.  Connect to the device wirelessly using SSID and password provided on the device information label or use an Ethernet cable connected to LAN port.

1/0:
programmable lnpuUOutput pins (Open Collector output max 30 V, 300 mA or Digital input where 0-6 V detected as logic low and 8-30 V – logic high).

LOGIN TO DEVICE

1. To enter the router’s Web interface (WebUI}, type http:/1192.168.1.1 into the URL field of your Internet browser.
2.  Use login information shown in image A when prompted for authentication.
3. After you login, you will be prompted to change your password for security reasons. The new password must contain at least 8 characters, including at least one uppercase letter, one lowercase letter and one digit. This step is mandatory and you will not be able to interact with the router’s WebUI before you change the password.
4.  When you change the router’s password, the Configuration Wizard will start. The Configuration Wizard is a tool used to setup some of the router’s main operating parameters.
5.  Go to Overview page and pay attention to the Signal Strength indication (image B). To maximize the cellular performance try adjusting the antennas or changing the location of your device to achieve the best signal conditions.

TECHNICAL INFORMATION

Radio specifications

RF technologies

Max RF power

| 3G,4G,WiFi

24 dBm@WCDMA,23 dBm@LTE,20 dBm@WiFi

**Bundled accessories specifications*
Power adapter| Input: 0.6 A@100-240 VAC, Output: 12 voe,1.5 A,4 pin plug
Mobile antenna| 698-960/1710-2690 MHz, 50 n, VSWR<3, gain 4 dBi, omnidirectional, SMA male connector
WiFi antenna| 2400-2483.5 MHz, 50 n, VSWR<2, gain** 5 dBi, omnidirectional, RP-SMA male connector

• Order code dependent.
• Higher gain antenna can be connected to compensate for cable attenuation when a cable is used. The user is responsible for the compliance with the legal regulations.

FCC Regulations

（15C）This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1.  This device may not cause harmful interference, and
2.  this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. (15B)This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•  Consult the dealer or an experienced radio/TV technician for help.

FCC RF Exposure Intormation
This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter and must be installed to provide a separation distance of at least 20cm from all persons.This transmiter must not be co-located or operatng in conjuncton with any other antenna or transmiter. This equipment should be installed and operated with a minimum distance of 20 centmeters between the radiator and your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>