Great Outdoors 71263-7-66 Black Outdoor Wall Light Instruction Manual
- October 30, 2023
- Great Outdoors
Table of Contents
Great Outdoors 71263-7-66 Black Outdoor Wall Light
Product Information
The product is a light fixture with model number 71263/7-66. It comes with a mounting plate (Part#A-020-125366), ground screw, mounting screws, wood screws, and anchors. The fixture wires are black and white, and the house wires are black (hot), white (neutral), and green or bare copper (ground). The product also includes a candle cover, with two options available: CCV21090PA-66 (Item#71263-66) and CCV21115P-66 (Item#71267-66).
Product Usage Instructions
- Before installing the product, shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.
- Unpack the new fixture carefully and lay out all the parts in a clear area.
- Consult a qualified electrician to ensure correct branch circuit conductor installation to prevent the risk of fire.
- Attach the mounting plate to the electrical box using the mounting screws provided.
- Connect the fixture wires to the house wires by matching the wire colors and securing them together with wire connectors.
- Attach the fixture to the mounting plate using the wood screws provided.
- Install the candle cover of your choice by aligning it with the fixture and twisting it into place.
- Caulk around the fixture to seal it against moisture.
- Finally, turn on power at the fuse box or circuit breaker box to test the product.
INSTALLATION INSTRUCTIONS
Model# 71263/7-66
READ AND SAVE THESE INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
PREPARING FOR INSTALLATION (Fig. 1)
-
Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.
-
Carefully unpack your new fixture and lay out all the parts in a clear area. Take care not to misplace any small parts necessary for installation.
-
Position the mounting plate (B) on the wall and mark the location of the two holes on the mounting plate where the plastic anchors (O) will be inserted. Drill holes into the wall and insert the plastic anchors (O).
-
Attach the mounting plate (B) to the outlet box (A) (not supplied) with outlet box screws (F). The side of mounting plate marked “GND” must face out. Then secure the two wood screws (P) into the plastic anchors (O).
-
The support cable (R) is provided to support the weight of the fixture while wiring. Align the fixture to mounting plate (B) and attach the end of support cable (R) into a slot located on mounting plate (B). Carefully allow the support cable (R) to support the weight of the fixture while wiring (Fig.1).
CONNECTING THE WIRES (Fig. 2) -
Connect the electrical wires as shown in Fig 2. with connectors (E), making sure that all wire connectors are secured. If your outlet box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (B) using the green screw (D) provided. After the wires are connected, carefully tuck them inside the outlet box.
FINISHING THE INSTALLATION (Fig. 1) -
Place the back plate (G) over mounting screws (C,4pcs), follow by rubber gasket (Q), then secure to wall using cap nuts (H,4pcs). (Fig 1)
-
To prevent moisture from entering the outlet box (A) and causing a short, use clear silicone sealant to outline the outside of fixture back plate (G) where it meets the wall leaving a space at bottom to allow moisture a means to escape (Fig.3)
-
To replace the glass, remove gaskets (M,8pcs) and loosening the screws (L,8pcs) to remove cover (K). Insert the new glass (J) into the fixture frame from the bottom. Secure the lower cover (K) by screwing screws (L,8pcs) until tight and reinstalling gaskets (M,8pcs) on the lower cover (K).
-
Install (4) four candelabra base bulbs (I) up to 40 Watts, or CFL or LED equivalent (not included), in accordance with the fixture specification. (DO NOT EXCEED THE MAXIMUM WATTAGE RATING) (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)
-
This fixture is ETL listed for wet location applications. Your installation is now complete. Return power to the outlet box and test the fixture.
“ CAUTION -RISK OF FIRE CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH CIRCUIT CONDUCTOR”
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>