Graywind GW-QZYM-TH00 Roller Shades Installation Manual
- June 12, 2024
- Graywind
Table of Contents
Graywind GW-QZYM-TH00 Roller Shades
Recommended tools
- Screw Gun
- Tape measure
- Screwdriver
- Level
- Pencil
Hardware included
Installing Screw:
Valance Hardware:
Motorized roller shade:
Motorized roller shade with fascia:
Dual Motorized roller shade:
Installation or removal Instructions
Bracket installation
For inside mount:
When installing the brackets, the distance from the first bracket mounting hole to the front of the jamb should be more than 3/4”. Both of the brackets should be at the same horizontal line. Two 1 1/4” hexagon screws are used for the installation of each bracket.
For outside mount:
When installing the brackets, the top of each bracket is parallel with the
edge of the window frame. The distance from the mounting holes of the brackets
to the front edge of the window frame should be more than 3/4”. Both of the
brackets should be at the same horizontal line. Two
1 1/4” hexagon screws are used for the installation of each bracket.
Bracket installation for the coupled shade:
The bracket installation for the coupled shade is the same as the single shade but uses a 36x6mm extension behind both side brackets. The center bracket should be at the same horizontal line as the two side brackets.??
Install the shade into the brackets:
Mount the shade (motor side) into the bracket (motor side), and then press the end plug into the mounting hole of the end plug bracket.
Removal
Use a screwdriver to release the end plug from the end plug bracket and then remove the motor side of the shade from the clutch bracket.
Installation and removal of motorized roller shade with fascia:
The brackets should be mounted level on both sides of the roller shade. Pay attention to the location of the brackets and make sure the left/right bracket is on the correct side.
For inside mount:
When installing the brackets, the distance from the front mounting hole of the brackets to the front edge of the window frame should be more than 3/4”. Ensure both of the brackets are at the same horizontal line. Two 1 1/4” hexagon screws are used for the installation of each bracket.
For outside mount:
When installing the brackets, the top of each bracket is parallel with the edge of the window frame. The distance from the mounting holes of the brackets to the front edge of the window frame should be more than 3/4”. Both of the brackets should be at the same horizontal line. Two 1 1/4” hexagon screws are used for the installation of each bracket.
Coupled shades:
The bracket installation for coupled shade is the same as a regular shade. Make sure the link bracket and the left/right brackets are level.
Inside mount of the brackets:
Be sure the center of the link bracket is aligned with the center of the left/right brackets.
Outside mount of the fascia bracket:
Attach two 6mm extensions on both the left and the right fascia brackets.
Common Fascia:
When installing the brackets, all of the brackets should be at the same horizontal line. Use a level to check. The bracket # from left to right is L1. L2. L3. L4, as shown below:
Install shade and fascia into the brackets:
- Install the motor end of the shade into the clutch bracket and the plug end into the plug end bracket.
- Install the fascia and bracket covers after installing the shade.
- Hook the top lip of the Fascia to the top of the bracket, tilt the Fascia downwards and make the bottom lip of the Fascia hook into the bottom lip of the bracket.
- Insert the bracket covers into the brackets after installing the fascia, as shown below:
Removal
- Make the bracket covers tilt outward to detach them from the brackets.
- Detach the bottom lip of the Fascia from the brackets. Then tilt the fascia upward to release the fascia from the brackets.
- After removing the fascia from the brackets, use a flathead screwdriver to take the plug end off the plug bracket, and then take motor end off of the clutch bracket.
Dual motorized roller shade installation or removal
For inside mount:
When installing the vertical dual brackets, the distance from the mounting hole of the vertical dual brackets to the front edge of the window frame should be more than 3/4”. Ensure both of the vertical dual brackets are at the same horizontal line. Use two 1 1/4” hexagon screws per bracket for installation.
For outside mount:
When installing the vertical dual brackets, the top of each vertical dual
bracket is parallel with the edge of the window frame. The distance from the
mounting holes of the vertical dual bracket to the front edge of the window
frame should be more than 3/4”. Both of the vertical dual brackets should be
at the same horizontal line. Each vertical dual bracket needs two 1 1/4”
hexagon screws and two 10mm spacer blocks for installation.
(The extension is not default, but used per shade specification when it is
provided)
Install the roller shade into the vertical dual brackets
Installation (inside & outside mount)
First, install the motor end of the front shade into the upper vertical dual clutch bracket, and then press the (end plug side) into the plug side of the vertical dual bracket. Install the back shade into the lower section of the vertical dual brackets the same way.
Removal (inside & outside mount)
Use a screwdriver to take the end plug off the top shade vertical dual bracket and then remove the (motor side) from the clutch vertical dual bracket. Remove the lower shade from vertical dual brackets the same way. As shown below:
Valance installation or removal
For inside mount:
When installing the valance brackets, ensure all the valance brackets are at the same horizontal line. Each valance bracket needs a 1 1/4″ hexagon screw for installation. The 1 1/4″ hexagon screw should be mounted in the horizontal line hole in the valance bracket, each valance bracket should be aligned with the valance clips.
For semi-inside mount:
When installing Extension Brackets, ensure all Extension Brackets are at the same horizontal line. Each Extension Bracket needs a 1 1/4″ hexagon screw for installation. The front edge of the brackets should be parallel with the edge of the window frame. Each Extension Bracket should be aligned with the valance clip. The extensions for left and right brackets will be provided according to shade specifications.
For outside mount:
When installing the Extension Brackets, ensure all the Extension Brackets are at the same horizontal line. Each Extension Bracket needs a 1 1/4″ hexagon screw for installation. The lower edge of the Extension Bracket should be parallel with the upper edge of the mounting bracket. Each Extension Bracket should be aligned with the valance clips.
Valance installation
For the inside mount, align the valance bracket with the valance clips and make the top of the valance tight against the top of the window, then insert the valance into the valance bracket. Adjust the valance position upward and downward if needed.
For semi-inside mount and outside mount:
- Connect the valance and the returns with the valance connector.
- Insert the valance bracket into the valance clip, and then insert the valance brackets into the extension brackets. Adjust the valance bracket position forward or backward to adjust the valance position. The valance position also can be adjusted upward and downward by moving the valance clips position on the valance brackets.
Attention: Please adjust the position of each valance bracket during installation to make sure the valance will not be concave inward but always keep level and smooth.
Battery wand installation
- Fix 2 battery wand clips to the wall next to the shade in a vertical line, and then attach the battery wand to the clips.
- Load 8 AA batteries into the battery wand and snap the battery wand into the clips. Make sure the end cover is on top.
- After both the shade and battery wand are installed, connect the power cord of the motor and the battery wand.
Attention: The motorized roller shade is heavy. Pay attention during installation.
FAQs
What is the main function of the Graywind roller shades?
Graywind roller shades are 100% blackout textured shades with a waterproof back layer. They ensure absolute privacy and offer additional energy savings. These shades are perfect for indoor spaces such as bedrooms, living rooms, patio sliding doors, and media rooms.
Are the roller shades child-safe?
Yes, these roller shades have a cordless design, making them safe for children and pets.
What's special about the 15-channel timing remote?
The 15-channel timing remote allows users to separately and group control up to 15 smart shades. It offers features like setting favorite positions and can be programmed for 20 different date-time groups.
How does the Bluetooth motor solution work?
The Bluetooth Motor Solution, or BLE Motor, works directly with the Graywind App through Bluetooth. It allows users to control the shades within a 99ft/30m signal range without needing a bridge. It is best suited for users who prefer controlling their blinds at home using a remote or app.
Can I control the shades with voice commands?
Yes, the Zigbee Motor Solution allows for voice control through compatible Echo devices. It works directly with several Echo models without needing a hub and allows for voice commands for various controls
Are custom dimensions available for the roller shades?
Yes, Graywind offers a Customize Now option for customers to provide custom dimensions and other details.
How long will it take to receive my custom order?
The production for custom orders takes about 3 workdays. Delivery requires an additional 5 workdays.
What kind of warranty and support does Graywind offer?
Graywind offers a two-year limited warranty on motors and remotes. They also provide long-term technical support for their products.
Can I control the roller shades using an app?
Yes, the Graywind app allows users to control the shades using their smartphone or tablet. The app provides features like percentage control, group creation, and setting timing schedules, depending on the motor option chosen.
What is unique about the AEOLUS Remote?
The AEOLUS remote boasts an ergonomic design, an all-black aesthetic with backlighting for visibility at night, and a removable silicone case. It offers multiple channels, a timing function, and the ability to set a favorite position.
Can you describe the fabric used in the shades?
The Graywind roller shades use a Jacquard woven fabric, which has a natural look and is complemented by a waterproof white back layer. This design ensures that light is blocked out, providing a private space.
How do the Graywind roller shades save energy?
The 100% blackout textured fabric paired with a waterproof back layer provides efficient insulation, thereby helping to regulate indoor temperatures and leading to potential energy savings.
Video- Product Overview
Download this PDF Link: Graywind GW-QZYM-TH00 Roller Shades Installation Manual
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>