THE GREAT OUTDOORS 71260-1-66 Black Outdoor Wall Light Instruction Manual

THE GREAT OUTDOORS 71260-1-66 Black Outdoor Wall Light

Product Information

The product is a wall-mounted light fixture with model number 71260/1-66. The fixture is designed for wet location applications and is ETL listed. The package includes a mounting plate, ground screw, mounting screws, backplate, rubber gasket, cap nuts, gaskets, cover, and medium base bulb (up to 60 Watts, or CFL or LED equivalent not included).

Product Usage Instructions

1. Before installation, shut off power at the fuse box or circuit breaker box.
2. Remove the old fixture including the mounting hardware.
3. Unpack the new fixture and lay out all the parts in a clear area.
4. Screw the mounting screws into the mounting plate ensuring they are spaced the same distance apart as the holes in the back plate.
5. Connect the electrical wires as shown in Fig 2 with connectors making sure that all wire connectors are secured. If your outlet box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate using the green screw provided. After the wires are connected, carefully tuck them inside the outlet box.
6. Place the backplate over mounting screws, follow by rubber gasket, then secure to wall using cap nuts.
7. To prevent moisture from entering the outlet box and causing a short, use clear silicone sealant to outline the outside of fixture back plate where it meets the wall leaving a space at bottom to allow moisture a means to escape.
8. To replace the glass, remove gaskets and loosening the screws to remove cover. Insert the new glass into the fixture frame from the bottom. Secure the lower cover by screwing screws until tight and reinstalling gaskets on the lower cover.
9. Install one medium base bulb up to 60 Watts, or CFL or LED equivalent (not included), in accordance with the fixture specification. DO NOT EXCEED THE MAXIMUM WATTAGE RATING.
10. After installation is complete, turn on power and test the fixture.

INSTALLATION INSTRUCTIONS

WARNING! SHUT THE POWER OFF AT THE FUSE OR CIRCUIT BREAKER.

PREPARING FOR INSTALLATION (Fig. 1)

1. Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.
2. Carefully unpack your new fixture and lay out all the parts in a clear area. Take care not to misplace any small parts necessary for installation.
3. Screw the mounting screws (C) into mounting plate (B) ensuring they are spaced the same distance apart as the holes in the back plate (G).
4. Attach mounting plate (B) using outlet box screws (F) to the outlet box (A) (not supplied). The side of mounting plate marked “GND” must face out. (Fig 1)
   • CONNECTING THE WIRES (Fig. 2)
5. Connect the electrical wires as shown in Fig 2. with connectors (E), making sure that all wire connectors are secured. If your outlet box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (B) using the green screw (D) provided. After the wires are connected, carefully tuck them inside the outlet box.
   • FINISHING THE INSTALLATION (Fig. 1)
6. Place the back plate (G) over mounting screws (C), follow by rubber gasket (Q), then secure to wall using cap nuts (H). (Fig 1)
7. To prevent moisture from entering the outlet box (A) and causing a short, use clear silicone sealant to outline the outside of fixture back plate (G) where it meets the wall leaving a space at bottom to allow moisture a means to escape. (Fig.3)
8. To replace the glass, remove gaskets (M,8pcs) and loosening the screws (L,8pcs) to remove cover (K). Insert the new glass (J) into the fixture frame from the bottom. Secure the lower cover (K) by screwing screws (L,8pcs) until tight and reinstalling gaskets (M,8pcs) on the lower cover (K).
9. Install (1) one medium base bulb (I) up to 60 Watts, or CFL or LED equivalent (not included), in accordance with the fixture specification. (DO NOT EXCEED THE MAXIMUM WATTAGE RATING) (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)
10. This fixture is ETL listed for wet location applications.

Your installation is now complete. Return power to the outlet box and test the fixture.

CAUTION-RISK OF FIRE CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH CIRCUIT CONDUCTOR”

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>