The Great Outdoors 72131-66 Noble Hill 1 Light Black Outdoor Lantern Sconce with Clear Glass Shades Instruction Manual
- June 11, 2024
- THE GREAT OUTDOORS
Table of Contents
The Great Outdoors 72131-66 Noble Hill 1 Light Black Outdoor Lantern
Sconce with Clear Glass Shades
Product Information
The product is a light fixture with two models – 72131-66 and 72132-66. The
package includes a mounting plate, mounting screws, ground screws, glass
panels, candle cover, and fixture wires. The fixture can accommodate
candelabra base bulbs up to 60 watts or CFL or LED equivalent.
The installation requires shutting off the power at the fuse or circuit
breaker and removing the old fixture including the mounting hardware. The
installation process involves preparing for installation, connecting the
wires, and finishing the installation. It is recommended to install the
fixture by a qualified electrician to ensure proper wiring and installation.
Product Usage Instructions
- Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.
- Carefully unpack your new fixture and lay out all the parts in a clear area. Take care not to misplace any small parts necessary for installation.
- Remove screws (F) and rubber washers (E) and separate mounting plate (C) from back plate (G).
- Position mounting plate (C) on the wall and mark the location of four drywall anchors (O). Pre-drill holes for drywall anchors (O). Insert drywall anchors (O) into the wall.
- Attach mounting plate (C) to outlet box (A) (Not included) with outlet box screws (D). Note: The side of the mounting plate marked GND must face out.
- Place woodscrews (N) through holes into drywall anchor (O) to secure mounting plate (C) as shown in Fig.1.
- Remove screws (K), separate cover (M) from fixture body (H), and install glass panels (L) into the holder of fixture body (H) and secure with tabs (I) on top and bottom.
- Install candelabra base bulbs (J) up to 60 watts or CFL or LED equivalent (not included) in accordance with the fixture specification. DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)
- Connect the electrical wires as shown in Fig.2. Make sure that all wire connectors (B) are secured. If your outlet box (A) has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (C) using the green screw provided.
- Tuck wire connectors neatly into outlet box (A).
- Align the back plate (G) onto a mounting plate (C) and secure it with rubber washers (E) and screws (F).
- Place cover (M) onto fixture body (H) and secure with screws (K).
- To prevent moisture from entering the outlet box (A) and causing a short, use clear silicone sealant to outline the outside of the back plate (G) where it meets the wall leaving a space at the bottom to allow moisture a means to escape. (Fig .3)
- Return power to the outlet box and test the fixture.
INSTALLATION INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU
DISJONCTEUR.
PREPARING FOR INSTALLATION (Fig. 1)
-
Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.
-
Carefully unpack your new fixture and lay out all the parts in a clear area. Take care not to misplace any small parts necessary for installation.
-
Remove screws (F) and rubber washers (E) and separate mounting plate (C) from back plate (G).
-
Position mounting plate (C) on the wall and mark the location of four drywall anchors (O). Pre-drill holes for drywall anchors (O). Insert drywall anchors (O) into the wall.
-
Attach mounting plate (C) to outlet box (A) (Not included) with outlet box screws (D).
Note: The side of the mounting plate marked “GND” must face out. -
Place woodscrews (N) through holes into drywall anchor (O) to secure mounting plate (C) as shown in Fig.1.
-
Remove screws (K), separate cover (M) from fixture body (H), and install glass panels (L) into holder of fixture body (H) and secure with tabs (I) on top and bottom.
-
Install candelabra base bulbs (J) up to 60 watts or CFL or LED equivalent (not included) in accordance with the fixture specification. —DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)
- CONNECTING THE WIRES (Fig. 2)
-
Connect the electrical wires as shown in Fig.2. Make sure that all wire connectors (B) are secured. If your outlet box (A) has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (C) using the green screw provided.
-
Tuck wire connectors neatly into outlet box (A).
- FINISHING THE INSTALLATION (Fig.1)
-
Align the back plate (G) onto a mounting plate (C) and secure it with rubber washers (E) and screws (F).
-
Place cover (M) onto fixture body (H) and secure with screws (K).
-
To prevent moisture from entering the outlet box (A) and causing a short, use clear silicone sealant to outline the outside of the back plate (G) where it meets the wall leaving a space at the bottom to allow moisture a means to escape. (Fig .3)
- Your installation is now complete. Return power to the outlet box and test the fixture.
- IMPORTANT: THE FIXTURE SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN TO ENSURE PROPER WIRING AND INSTALLATION.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>