The Great Outdoors 73331-66A Knoll Road 4-Light Black Outdoor Wall Mount Instruction Manual

The Great Outdoors 73331-66A Knoll Road 4-Light Black Outdoor Wall Mount

Product Information

Product Usage Instructions

1. Before starting the installation, make sure to shut off the power at the fuse or circuit breaker.
2. Remove the old fixture, including the mounting hardware, carefully.
3. Unpack your new fixture and lay out all the parts on a suitable surface.
4. Refer to Fig. 1 for the following steps:
   • Mount the mounting plate using the provided mounting screw (2 screws).
   • Secure the ground screw to the mounting plate.
5. Refer to Fig. 2 for the following step:
   • Connect the black or smooth fixture wire to the corresponding house wire.
   • Connect the white or ribbed fixture wire to the corresponding house wire.
   • Connect the green or bare copper fixture wire (ground) to the corresponding green house wire (ground).
6. Refer to Fig. 3 for the following step:
   • Apply caulk around the backplate to ensure a secure installation.
7. Your installation is now complete. Restore power and test the fixture.
8. Note: The illustration in Fig. 1 is for installation purposes only and may or may not be identical to the fixture purchased.

Important: If you have any difficulties or questions during the installation process, please consult a professional electrician.

LA-3614E

INSTALLATION INSTRUCTIONS

Item#73331-66A (New. 2023/02/16)
READ AND SAVE THESE INSTRUCTIONS

WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.

MOUNTING THE FIXTURE (Fig.1)

1. Shut off the power at the circuit breaker and remove the old fixture, including the mounting hardware.

2. Carefully unpack your new fixture and lay out all the parts on a clear area. Take care not to lose any small parts necessary for installation.

3. Pull up latch (H) and open the door. Install glass Panels (K) (1pc, Size: L550mm x W160mm), (J) (2pcs, Size: L550mm x W132mm), (L) (1pc, Size: L527mm x W137mm) onto fixture body (C) and secure with tabs inside frame.

4. Position mounting plate (A) on wall and mark location of the four mounting holes. Pre-drill the holes for dry wall anchors (N). Insert drywall anchors (N) into wall.

5. Attach mounting plate (A) to junction box using mounting screws (B) (Size: #8-32N*L0.5”). The side of mounting plate marked “GND” must face out.

6. Secure mounting plate (A) by inserting wood screws (M) through holes on mounting plate into the plastic anchors (N).

7. The support cable is provided to support weight of fixture while wiring. Align fixture to mounting plate (A) and attach hook (P) on the end of support cable (O) into a slot located on mounting plate (A). Carefully allow the support cable (O) to support weight of the fixture while wiring.
   CONNECTING THE WIRES (Fig. 2)

8. Connect the electrical wires as shown in (Fig. 2). Making sure that all wire connectors are secured. If your outlet box has a ground wire (green or bare copper), connect fixture’s ground wire to it. Otherwise, connect fixture’s ground wire directly to mounting plate (A) using green screw provided.

9. Tuck wire connectors neatly into the junction box.
   COMPLETING THE INSTALLATION

10. Align fixture body (C) onto mounting plate (A) and secure with plastic washer (E) and screws (D).

11. To prevent moisture from entering the outlet box and causing a short, use clear caulking (i.e. Indoor/Outdoor Silicone Sealant) to outline outside of fixture back-plate where it meets the wall leaving a space at bottom to allow moisture a means to escape (Fig.3).

12. To prevent moisture from entering the outlet box and causing a short, use clear caulking (i.e. Indoor/Outdoor Silicone Sealant) to outline outside of fixture back-plate where it meets the wall leaving a space at bottom to allow moisture a means to escape (Fig.3).

13. Place candle covers (F) over sockets (I).

14. Install (4) four candelabra base bulbs (G) up to 60 watts or CFL or LED equivalent (not included) in accordance with the fixture specification. (DO NOT EXCEED THE SPECIFIED WATTAGE!) (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).

15. Close the door and re-latch (H) onto door.
    Your installation is now complete. Return power and test the fixture.

Note: Illustration (Fig. 1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>