The Great Outdoors 72795-143-L Shore Pointe 1 Light Oil Rubbed Bronze Outdoor LED Post Light Instruction Manual

The Great Outdoors 72795-143-L Shore Pointe 1 Light Oil Rubbed Bronze

Outdoor LED Post Light

Product Information

The product is a light fixture with model numbers 72795-143-L and 72796-143-L. It comes with an LED module that has a wattage of 11W for model 72795-143-L and 8W for model 72796-143-L. The fixture is ETL listed for wet location applications, making it suitable for outdoor use. The fixture also includes a glass component, base cup, finials, and mounting screws.

Product Usage Instructions

1. Before starting the installation, shut off power at the fuse box or circuit breaker box.
2. Remove the old fixture and its mounting hardware.
3. Unpack the new fixture and lay out all the parts in a clear area, ensuring not to misplace any small parts needed for installation.
4. Pull out the black, white, and ground wires from the base cup.
5. Place the glass in the middle of the base cup and thread it into the fixture frame. Secure the base cup with finials until tight.
6. Connect the electrical wires as shown in Fig. 2, making sure all wire connectors are secured. If your post has a ground wire, connect the fixture ground wire to it. If not, consult an electrician for proper grounding.
7. Carefully tuck the wire connectors inside the base cup.
8. Align the base cup with the post and secure it with mounting screws.
9. Make sure not to exceed the maximum wattage rating mentioned in the LED information section.
10. The fixture is suitable for wet location applications.

Replacing LED Module

The LED module can be replaced by a qualified electrician without cutting any wires or damaging any decorative elements attached to the fixture. Follow these steps:

1. Shut off power and loosen the finials to separate the fixture frame from the base cup. Remove the glass.
2. Loosen the screws and washers on the LED module and carefully remove it.
3. To install a new LED module, reverse the steps mentioned above.

Note: The LED module should be provided by a specified supplier with the respective Glass Code# G72795 for model 72795-143-L and G72796 for model 72796-143-L.

After completing the installation, return power to the outlet box and test the fixture. If there are any concerns or doubts, it is recommended to consult a qualified electrician to ensure correct branch circuit conductor and minimize the risk of fire.

INSTALLATION INSTRUCTIONS

Model# 72795-143-L / #72796-143-L
READ AND SAVE THESE INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

PREPARING FOR INSTALLATION (Fig. 1)

1. Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.

2. Carefully unpack your new fixture and lay out all the parts in a clear area.
   Take care not to misplace any small parts necessary for installation.

3. Pull black, white, and ground wires out of base cup (D).

4. Place glass (F) in the middle of base cup (D), and thread into fixture frame (G). Secure base cup (D) with finials (E) until tight.
   CONNECTING THE WIRES (Fig. 2)
   Connect electrical wires as shown in Fig. 2 making sure that all wire connectors (B) are secured. If your post (A) (Not included) has a ground wire (green or bare copper), connect fixture ground wire to it. If not, consult your electrician for proper grounding.

5. Tuck wire connectors carefully inside base cup (D).

6. Align base cup (D) with post (A) and secure with mounting screws (C). (Fig.1)

7. LED information (#72795-143-L: 1 x AC LED 11W included. #72796-143- L: 1 x AC LED 8W included.) (DO NOT EXCEED THE MAXIMUM WATTAGE RATING) (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)

8. This fixture is ETL listed for wet location applications.

Replacing LED

Replacing LED module (Fig.3)

The LED module can be replaced by a qualified electrician without cutting of wire and without damage to any decorative element to which the fixture is attached. See installation steps for more details (Fig.3).

• Shut off power. Loosen finials (E) and separate fixture frame (G) from base cup (D). Remove glass (F).
• Loosen screws (J) and washers (L) on the LED module (K), then carefully remove LED module (K).
• Reverse steps a-b for installing the new LED module.

Note: The LED module should be provided by a specified supplier.
Your installation is now complete. Return power to the outlet box and test the fixture.

“CAUTION-RISK OF FIRE CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH CIRCUIT CONDUCTOR”

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>