ZEVNI A04643 Benet 10-Light Black-Gold Modern-Contemporary Chandelier Instruction Manual

ZEVNI A04643 Benet 10-Light Black-Gold Modern-Contemporary Chandelier

INTRODUCTION

WARNING (To reduce the risk of fire, electric shock, or personal injury):

1. We suggest installation by a licensed electrician.

2. Please read the instruction carefully and save it as you may need it at a later time.

3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
   » Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
   » Place the wall switch in the “OFF” position.

4. Mounting surface should be clean, dry, flat, strong enough and 1/4″ larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16″ should be corrected as required.

5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.
   

6. Make sure the voltage you are using is 120V. The maximum wattage is 33W.

7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp. 8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.

8. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.

CLEANING
To clean, wipe the fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

TOOLS REQUIRED B

Before starting assembly and installation please prepare the needed (NOT INCLUDED): tools as below picture Ladder

PARTS TYPE & QTY INCLUDING

(B) Mounting plate (1)
(C) Green ground screw (1)
(E) Canopy (1)
(F) Stud (2)
(G) Lock nut (5)
(H) Cable (5)
(I) Arm (5)
(J) Screw (5)
(K) Spanner (1)

ACCESSORIES & QTY ENCLOSED

(A) Plastic wire connector (3) (D) Mounting screw (2)

ASSEMBLY & INSTALLATION INSTRUCTIONS:

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

2. Turn off power Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
   » Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
   » Place the wall switch in the “OFF” position

3. Unscrew studs (F) from canopy (E) then remove mounting plate (B).

4. » ●Find the left and right sides of arms (I).
   ● Align left side of one arm (I) and right side of the other arm (I).
   ● Secure different sides of two arms (I) with screws (J).
   ● Do the same to the remaining arms (I).
   

5. Attach mounting plate (B) to the outlet box with mounting screws (D)

6. Make wire connections
   Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.

7. Raise canopy (E) to the ceiling and secure canopy (E) in place by threading studs (F) into mounting plate (B) and canopy (E).
   CLEANING
   
   Connect ground wires according to the below chart
   
   Connect wires according to the below chart
   ** Connect Black or Red Supply Wire to:| Connect**

White Supply Wire to:

---|---
Black| White
Parallel cord (round & smooth)| Parallel cord (square & ridged)
Clear, Brown, Gold or Black without tracer| Clear, Brown, Gold or Black with tracer
Insulated wire(other than green) with copper conductor| Insulated wire(other than green) with silver conductor
8. To adjust the hanging height of the fixture:
To adjust the length of cables (H):
● Press down and hold lock nuts (G) by hand;
● Pull or push cables (H) in and out of canopy (E) to increase or decrease the hanging height.

9. Check everything is already installed properly, then you could turn on the light. Enjoy!
   

• Note: When parallel wires (SPT I & SPT ll) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)
  Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box

+1 850 296 2377 Working hours : Mon – Fri 9:00 – 16:00 EST
homecustomercare@outlook.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>