The Great Outdoors 72794-143-L Shore Pointe 1 Light Oil Rubbed Bronze Outdoor LED Pendant Light Instruction Manual

The Great Outdoors 72794-143-L Shore Pointe 1 Light Oil Rubbed Bronze

Outdoor LED Pendant Light

Product Information:

This product is a light fixture model number 72794-143-L / 72797-143-L. It includes an LED module with different wattage options: 8W for model 72794-143-L and 11W for model 72797-143-L. The fixture is ETL listed for wet location applications, and it needs to be installed under cover to ensure its proper functioning.

Product Usage Instructions

1. Before starting the installation, make sure to shut off the power at the fuse box or circuit breaker.

2. Remove the old fixture, including the mounting hardware.

3. Carefully unpack the new fixture and lay out all the parts in a clear area. Take care not to misplace any small parts necessary for installation.

4. Thread all thread (G) into cross bar (B) and secure it with a lock washer (E).

5. Connect the electrical wires according to Fig.2. Ensure that all wire connectors are securely connected. If your outlet box (A) has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the cross bar (B) using the green screw (C) provided.
   Tuck the wire connectors neatly into the outlet box (A).

6. Raise the canopy (H) over the ceiling loop (I) and secure it with a lock collar (J).

7. Make sure not to exceed the maximum wattage rating mentioned for the LED module. (#72794-143-L: 1 x AC LED 8W included. #72797-143-L: 1 x AC LED 11W included.)

8. This fixture is suitable for wet locations, but it needs to be installed under cover.

9. If you need to replace the LED module, follow the steps provided in Fig.3. Make sure to shut off the power, remove the glass panel, and carefully replace the LED module without damaging any decorative elements.

10. After completing the installation, return power to the outlet box and test the fixture.

11. Consult a qualified electrician if you have any concerns or questions regarding the branch circuit conductor or to ensure correct installation.

Note: It is important to use proper chain pliers (not included) to open and close the chain included with this fixture. Do not use other tools that may twist or stress the chain links. Refer to the diagram for proper chain pliers.

Note: The LED module should be provided by a specified supplier.

INSTALLATION INSTRUCTIONS

Mode# 72794-143-L/ 72797-143-L
READ AND SAVE THESE INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

PREPARING FOR INSTALLATION

(Fig. 1)

1. Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.

2. Carefully unpack your new fixture and lay out all the parts in a clear area.
   Take care not to misplace any small parts necessary for installation.

3. Thread all thread (G) into cross bar (B) and secure with lock washer (E) and hex nut (F). Note: The length of all thread into cross bar (B) may be adjusted if necessary.

4. Thread other end of all thread (G) into ceiling loop (I) until snug.

5. Attach cross bar (B) assembly using outlet box screws (D) to outlet box (A) (Not included). The side of cross bar (B) marked “GND” must face out.

6. Determine desired hanging height and use a pair of proper chain pliers to remove and discard excess chain.

7. Attach one quick link (L) to end of chain (K) and then to fixture loop (M), close quick link (L). Slip lock collar (J) and canopy (H) over chain and allow them to rest on fixture body. Attach another quick link (L) to other end of chain (K) and then to ceiling loop (1), close quick link (L).

8. Carefully lace fixture’s wires through chain. Feed fixture wires through ceiling loop (I) and all thread assembly.

9. Thread glass (O) from the bottom of fixture frame.
   CONNECTING THE WIRES (Fig. 2)

10. Connect the electrical wires as shown in Fig.2. Making sure that all wire connectors are secured. If your outlet box (A) has a ground wire (green or bare copper), connect fixture’s ground wire to it. Otherwise, connect fixture’s ground wire directly to cross bar (B) using green screw (C) provided.

11. Tuck wire connectors neatly into the outlet box (A).
    COMPLETTING THE INSTALLATION (Fig. 1)

12. Raise canopy (H) over ceiling loop (1) and secure with lock collar (J).

13. LED information (#72794-143-L: 1 x AC LED 8W included. #72797-143-L: 1 X AC LED 11W included.) (DO NOT EXCEED THE MAXIMUM WATTAGE RATING) (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)

14. This fixture is ETL listed for wet location applications. Needs to be installed under the cover.
    Replacing LED module (Fig.3)
    The LED module can be replaced by a qualified electrician without cutting of wire and without damage to any decorative element to which the fixture is attached.

Notice: It is important to use proper chain pliers (Not included) To OPEN and CLOSE the chain included with this fixture. Do not open them with other tools that may twist or stress the chain links. It is important to use proper chain pliers like the ones shown in the diagram.

See installation steps for more details (Fig.3).

• Shut off power. Remove glass (0), loosen screws (Q) and remove glass panel (R).
• Loosen screws (P) and washers (S) on LED module (T), then carefully pull out the plug inside top cover, and disconnect plug on wires. Carefully remove LED module (T).
• Reverse steps a-b for installing the new LED module.

Note: The LED module should be provided by a specified supplier.
Your installation is now complete. Return power to the outlet box and test the fixture.
“CAUTION-RISK OF FIRE CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH CIRCUIT CONDUCTOR’

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>