UBIQUITI Edgeswitch ES-10X Gigabit Switch User Guide

ES-10X Quick Start Guide

Package Contents

Installation Requirements

• Wall-mounting (optional)
  Drill with 6 mm drill bit
  Phillips screwdriver

• For indoor applications, use Category 5 (or above) UTP cabling approved for indoor use.

• For outdoor applications, shielded Category 5 (or above) cabling should be used for all wired Ethernet connections and should be grounded through the AC ground of the power supply.
  We recommend that you protect your networks from harmful outdoor environments and destructive ESD events with industrial-grade, shielded Ethernet cable from Ubiquiti. For more details, visit: ui.com/toughcable

Note: Although the cabling can be located outdoors, the EdgeSwitch itself should be housed inside a protective enclosure.

Hardware Overview

1. System LED

Flashing White| Bootup in Progress
White| Ready for Use
Not Connected to Ubiquiti Internet Service Provider (UISP™)
Blue| Ready for Use
Connected to UISP
Steady Blue with
Occasional Flashing| Ready for Use
Unable to Connect to UISP
Quickly Flashing Blue| Used to Locate a Device in UISP
Alternating Blue/White| Firmware Upgrade in Progress
2. RJ45 Speed/Link/Activity LED (Ports 1 – 8)
Off| No Link
Amber| Link Established at 10/100 Mbps
Flashing Indicates Activity
Green| Link Established at 1000 Mbps
Flashing Indicates Activity
3. SFP Link/Activity LED (Ports 9 – 10)
Green| Link Established at 1 Gbps
Flashing Indicates Activity
4. RJ45 (Ports 1 – 8)
RJ45 ports support 10/100/1000 Ethernet connections.
PoE In (Port 1) Supports 24V Passive PoE input.
PoE Out (Port 8) Supports 24V Passive PoE passthrough.
5. SFP (Ports 9 – 10)
Hot-swappable SFP ports support 1 Gbps connections. If you use a copper
Ethernet module (example: UF-RJ45-1G), power off the EdgeSwitch before
insertion; otherwise there may be a device reboot.
6. Reset Button
To reset to factory defaults:
1. Disconnect power from the EdgeSwitch.
2. Reconnect power while holding the Reset button. The port LEDs will light up in sequential order (this takes approximately five seconds).
3. When the port 1 LED flashes again, release the Reset button.
7. Power
Connect the included Power Adapter to the Power port.
8. Grounding Point
Ground bonding point for an optional ground wire.

Hardware Installation

The optional EdgeRouter™ Rackmount Kit, model ER-RMKIT, is sold separately.
WARNING: The EdgeSwitch ES-10X must not be stacked. Do not place it on top of another switch. Do not place anything on top of the ES-10X.

Wall Mounting

Grounding the EdgeSwitch (Recommended)

Connecting Power

Note: Only one power source can be used at any one time. With both power sources connected, the input with the highest voltage will be used; the other power source defaults to backup.

Connecting Ethernet

WARNING: Before enabling PoE passthrough, ensure that the connected PoE device supports 24V Passive PoE.

Using SFP Ports

For information about compatible fiber SFP modules, visit: ubnt.link/SFP_DAC_Compatibility

Accessing the Configuration Interface

The device is set to DHCP by default, so it will try to automatically obtain an IP address. If that fails, then it will use the default fallback IP address, 192.168.1.20.
Proceed to the appropriate section, DHCP or “Fallback IP Address”:
DHCP
Use one of the following methods:
Set up the DHCP server to provide a specific IP address to the device based on its MAC address (on the label).
Let the device obtain an IP address and then check the DHCP server to see which IP address was assigned.

1. Launch your web browser. Type the appropriate IP address in the address field.
   Press enter (PC) or return (Mac).

2. Enter ubnt in the Username and Password fields. Click Sign In.
   The EdgeSwitch Configuration Interface will appear. Customize additional settings as needed. For 24V Passive PoE configuration, refer to “Configuring PoE Settings”.
   For more information, refer to the EdgeSwitch documentation, which is available at ui.com/download/edgemax

Fallback IP Address

1. Ensure that your computer (or other host system) is connected to the device.
2. Configure the Ethernet adapter on your host system with a static IP address on the 192.168.1.x subnet.
3. Launch your web browser. Type the appropriate IP address in the address field (192.168.1.20 is the default fallback IP address). Press enter (PC) or return (Mac).
4. Enter ubnt in the Username and Password fields. Click Sign In.
5. The EdgeSwitch Configuration Interface will appear. Click the System Settings tab.
6. Change the IP Address to a unique IP address. Click Apply.

Note: If you change the IP settings, then the session will be cut off, and you will need to reconnect to the device using the new IP address.

Customize additional settings as needed. For 24V Passive PoE configuration, refer to “Configuring PoE Settings”. For more information, refer to the EdgeSwitch
documentation, which is available at ui.com/download/edgemax

Configuring PoE Settings
The PoE setting for port 8 is set to Off by default.
WARNING: Before activating PoE, ensure that the connected device supports passive PoE and the supplied voltage.
On the Dashboard tab, click the PoE setting of port 8. Then select 24V.

UISP Management

You can manage your device using UISP, which lets you configure, monitor, upgrade, and back up your devices using a single application. Get started at uisp.ui.com

Specifications

LEDs
System
RJ45 Data Ports
SFP Data Ports| Status
Link/Speed/Activity
Link/Activity
Networking Interfaces| (8) 10/100/1000 Mbps RJ45 Ports
(2) 1 Gbps SFP Ports
Management Interface| Ethernet In-Band
Certifications| CE, FCC, IC
ESD/EMP Protection| Air: ± 24 kV, Contact: ± 24 kV
Operating Temperature| -10 to 50° C (14 to 122° F)
Operating Humidity| 5 to 95% Noncondensing
Shock and Vibration| ETSI300-019-1.4 Standard

PoE (Port 8)

Safety Notices

1. Read, follow, and keep these instructions.
2. Heed all warnings.
3. Only use attachments/accessories specified by the manufacturer.
   WARNING: Failure to provide proper ventilation may cause fire hazard. Keep at least 20 mm of clearance next to the ventilation holes for adequate airflow.
   WARNING: Do not use this product in location that can be submerged by water.
   WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.

Electrical Safety Information

1. Compliance is required with respect to voltage, frequency, and current requirements indicated on the manufacturer’s label. Connection to a different power source than those specified may result in improper operation, damage to the equipment or pose a fire hazard if the limitations are not followed.
2. There are no operator serviceable parts inside this equipment. Service should be provided only by a qualified service technician.
3. This equipment is provided with a detachable power cord which has an integral safety ground wire intended for connection to a grounded safety outlet.
   a. Do not substitute the power cord with one that is not the provided approved type. Never use an adapter plug to connect to a 2-wire outlet as this will defeat the continuity of the grounding wire.
   b. The equipment requires the use of the ground wire as a part of the safety certification, modification or misuse can provide a shock hazard that can result in serious injury  or death.
   c. Contact a qualified electrician or the manufacturer if there are questions about the installation prior to connecting the equipment.
   d. Protective earthing is provided by Listed AC adapter. Building installation shall provide appropriate short-circuit backup protection.
   e. Protective bonding must be installed in accordance with local national wiring rules and regulations.

Limited Warranty

ui.com/support/warranty
The limited warranty requires the use of arbitration to resolve disputes on an individual basis, and, where applicable, specify arbitration instead of jury trials or class actions.
Compliance
FCC
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions.
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation. protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operations of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

ISED Canada
CAN ICES-3(A)/NMB-3(A)
Australia and New Zealand
Warning: This equipment is compliant with Class A of CISPR 32. In a residential environment this equipment may cause radio interference.

CE Marking
CE marking on this product represents the product is in compliance with all directives that are applicable to it.

WEEE Compliance Statement
Declaration of Conformity
Online Resources

© 2022 Ubiquiti Inc. All rights reserved.

References

• Ubiquiti - Rethinking IT
• Ubiquiti - Warranty
• UniFi - Rethinking IT - Ubiquiti
• UISP Cloud Access Portal
• community.ubnt.com/
• WEEE Compliance Statement
• UISP Cloud Access Portal
• UniFi - Introduction - Ubiquiti
• Software Downloads - Ubiquiti
• Software Downloads - Ubiquiti
• Ubiquiti - Warranty

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>