UBIQUITI POE-50-60W POE Injector User Guide

UBIQUITI POE-50-60W POE Injector

Package Content

• PoE injector
• Power cord

Hardware Description

• PoE and LAN port
• Power input
• LAN activity indicator
• Gigabit LAN port
• Remote reset button
• Reset ability button

Installation

1. Connect a network cable to the PoE port on the injector and the other end to the Ubiquiti device you want to power (see device specifications).
2. Connect a network cable to the LAN port of the injector and the other end to the router or switch de su red local.
3. Connect the power cord to the injector and the other end to an electrical outlet.
4. Optionally, the PoE injector can be fixed to the wall or some
   other surfaces, follow the instructions in the following image.

Specifications

• Model: POE-50-60W, POE-50-60W-WH
• Dimensions: 101 x 60 x 33 mm (3.98 x 2.36 x 1.30)
• Weight: 192 g (6.77 ounces)
• Output voltage: 50 V DC at 1.2 A
• LAN activity indicator: No
• Gigabit LAN port: Yes
• Remote reset button: No
• Reset ability button : No
• Rated voltage: 100-240 V AC at 50/60 Hz
• Input current: 1.3 A at 120 V AC, 0.75 A at 230 V AC

Note: Please refer to the product manual for detailed technical specifications.

Product Usage Instructions

1. Ensure that the PoE injector is connected to a power outlet, and the Ubiquiti device is connected to the PoE port on the injector using a network cable.
2. Connect a network cable to the LAN port of the injector and the other end to the router or switch on your local network.
3. The LAN activity indicator will not show any activity as it is not available on this model.
4. The PoE injector does not have a reset button or a remote reset feature.
5. Ensure that the input voltage matches the rated voltage of the PoE injector before connecting the power cord.

Package content

hardware description

Installation

1. Connect a network cable to the PoE port on the injector and the other end to the Ubiquiti device you want to power (see device specifications).
2. Connect a network cable to the LAN port of the injector and the other end to the router or switch de su red local.
3. Connect the power cord to the injector and the other end to an electrical outlet. stream.
4. Optionally, the PoE injector can be fixed to the wall or some other surface, follow the instructions in the following image.

specs

safety instructions

1. Read, follow and save these instructions.
2. Pay attention to all warnings.
3. Only use the devices or accessories indicated by the manufacturer.

• ADVERTENCIA: Superficie caliente. No tocar.
• ADVERTENCIA: No utilice este producto en un lugar en el que pueda quedar sumergido en agua.
• ADVERTENCIA: Este producto no debe quedar expuesto a goteo o salpicaduras por líquidos.

electrical safety information

1. It is mandatory to comply with the current, frequency, and voltage requirements indicated on the manufacturer’s label. Connection to a power source other than those specified may result in malfunction, equipment damage, or fire hazard if limitations are not followed.
2. This equipment contains no operator-serviceable parts. Only a qualified service technician should provide services.
3. This equipment is supplied with a detachable power cord that has an integral safety ground wire designed to be connected to a safety ground. a. Do not substitute the power cord with one other than the approved type provided. Never use an adapter plug to connect to a two-wire outlet, as it will break the continuity of the ground wire.

• The equipment requires the use of the ground wire as part of the safety certification. Modification or misuse can create a shock hazard, which could cause serious injury or death.
• If you have any questions about the installation, contact a qualified electrician or the manufacturer before connecting the equipment.
• The indicated AC adapter provides a safety ground. For installation in a building, adequate short-circuit backup protection must be provided. and. A protective connection must be installed in accordance with national wiring rules and regulations.

limited warranty

ui.com/support/warranty
The limited warranty requires arbitration to resolve disputes on a case-by- case basis and, where appropriate, specify arbitration instead of jury trials or class actions.
Compliance

FCC

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions.

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide acceptable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

CE marked

El marcado CE de este producto indica que el producto cumple con todas las directivas aplicables.

References

• Ubiquiti - Warranty
• Ubiquiti - Warranty

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>