NORDIC 18V Cordless Blower Vacuum User Manual
- June 9, 2024
- NORDIC
Table of Contents
NORDIC 18V Cordless Blower Vacuum
PRODUCT SPECIFICATION
- Voltage: 18V
- Vacuum force: ≥4.5KPa
- Air speed: ≥63.5m/s
- A weighted sound pressure level: LpA: 90,7dB(A) ; KpA=3dB(A)
- A weighted sound power level: LwA: 98,6dB(A) ; KwA=3dB(A)
- Typical weighted vibration: ah=1,05m/s2 ;
- Uncertainty: k=0,5m/s2
GENERAL POWER TOOL SAFETY WARNINGS
Read all safety warnings and instructions. Failure to heed warnings and follow
instructions may result in electric shock, fire and/or serious injury.
Keep safety warnings and instructions for future reference.
The term “power tool” in the safety warnings refers to your mains operated
(corded) power tool or battery- operated (cordless) power tool.
WORKING AREA
- Keep working area clean and well lit. Untidy and dark areas can lead to accidents.
- Do not operate power tools in potentially explosive surroundings, for example, in the presence of inflammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
- Keep children and bystanders at a distance when operating a power tool. Distractions can cause you to lose control of it.
ELECTRICAL SAFETY
- Always check that the power supply corresponds to the voltage on the rating plate.
- Power tool plugs must match the outlet. Never modify the plug in any way. Do not use adapter plugs with earthed power tools. Unmodified plugs and matching outlets will reduce the risk of an electric shock.
- Avoid body contact with earthed surfaces such as pipes, radiators, kitchen ranges and refrigerators. There is an increased risk of an electric shock if your body is earthed.
- Do not expose power tools to rain or wet conditions. If water gets inside a power tool, it will increase the risk of an electric shock.
- Do not damage the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep the cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of an electric shock.
- When operating a power tool outdoors, use an extension cable suitable for outdoor use. Using a cord suitable for outdoor use reduces the risk of an electric shock.
- If operating a power tool in a damp location is unavoidable, use a power supply protected by a residual current device (RCD). Using an RCD reduces the risk of an electric shock.
PERSONAL SAFETY
-
Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool when you are tired or under the influence of drugs, alcohol or medication. A moment of inattention when operating a power tool may result in serious personal injury.
-
Use safety equipment. Always wear eye protection. Using safety equipment such as a dust mask, non-skid safety shoes, a hard hat, or hearing protection whenever it is needed will reduce the risk of personal injury.
-
Avoid accidental starts. Ensure the switch is in the off position before inserting the plug. Carrying power tools with your finger on the switch or plugging in power tools when the switch is in the on position makes accidents
more likely. -
Remove any adjusting keys or spanners before turning on the power tool. A spanner or key left attached to a rotating part of the power tool may result in personal injury.
-
Do not reach out too far. Keep your feet firmly on the ground at all times. This will enable you retain control over the power tool in unexpected situations.
-
Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from the power tool. Loose clothes, jewellery or long hair can become entangled in the moving parts..
-
If there are devices for connecting dust extraction and collection facilities, please ensure that they are attached and used correctly. Using such devices can reduce dust-related hazards.
POWER TOOL USE AND CARE
- Do not expect the power tool to do more than it can. Use the correct power tool for what you want to do. A power tool will achieve better results and be safer if used in the context for which it was designed.
- Do not use the power tool if the switch cannot turn it on and off. A power tool with a broken switch is dangerous and must be repaired.
- Disconnect the plug from the power source before making adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
- Store power tools, when not in use, out of the reach of children and do not allow people who are not familiar with the power tool or these instructions to operate it. Power tools are potentially dangerous in the hands of untrained users.
- Maintain power tools. Check for misalignment or jammed moving parts, breakages or any other feature that might affect the operation of the power tool. If it is damaged, the power tool must be repaired. Many accidents are caused by using poorly maintained power tools.
- Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to jam and are easier to control.
- Use the power tool, accessories and cutting tools, etc., in accordance with these instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work which needs to be done. Using a power tool in ways for which it was not intended can lead to potentially hazardous situations.
SERVICE
Your power tool should be serviced by a qualified specialist using only
standard spare parts. This will ensure that it meets the required safety
standards.
ADDITIONAL SAFETY INSTRUCTIONS FOR BATTERIES AND CHARGERS
Use only batteries and chargers applicable for this machine.
BATTERIES
- Never attempt to open for any reason.
- Do not store in locations where the temperature may exceed 40 °C.
- Charge only at ambient temperatures between 4 °C and 40 °C.
- When disposing of batteries, follow the instructions given in the section “Protecting the environment”.
- Do not cause short circuits. If connection is made between the positive (+) and negative (-) terminal directly or via accidental contact with metallic objects, the battery is short circuited and an intense current will flow causing heat generation which may lead to casing rupture or fire.
- Do not heat. If batteries are heated to above 100 °C, sealing and insulating separators and other polymer components may be damaged resulting in electrolyte leakage and/or internal short circuiting leading to heat generation causing rupture or file. Moreover do not dispose of the batteries in fire, explosion and/or intense burning may result.
- Under extreme conditions, battery leakage may occur. When you notice liquid on the battery, proceed as follows:
- Carefully wipe the liquid off using a cloth. Avoid skin contact.
- In case of skin or eye contact, follow the instructions below:
- Immediately rinse with water. Neutralize with a mild acid such as lemon juice or vinegar.
- In case of eye contact, rinse abundantly with clean water for at least 10 minutes.
- Consult a physician.
Fire hazard! Avoid short-circuiting the contacts of a detached battery. Do not incinerate the battery.
CHARGERS
- Never attempt to charge non-rechargeable batteries.
- Have defective cords replaced immediately.
- Do not expose to water.
- Do not open the charger.
- Do not probe the charger.
- The charger is intended for indoor use only.
SYMBOLS
In this manual and/or on the machine the following symbols are used:
- Denotes risk of personal injury or damage to the tool.
- Read manual before use
- Wear eye protection
- Wear ear protection
- Wear safety gloves
- Wear respiratory protection
- In accordance with essential requirements of the European directive(s)
- Class II – The machine is double insulated; Earthing wire is therefore not necessary (only for charger)
- Ambient temperature 40°C max. (only for battery)
- Do not expose charger and battery pack to water
- Use battery and charger only in closed rooms
- Do not incinerate battery pack or charger
PRODUCT ACCESSORIES
- Wind tube
- Handle angle adjust button
- Switch
- Wind inlet
- Dust bag
- Battery (not included)
- Charger (not included)
- Battery latch button;
- LED button
BEFORE YOU START
BLOWING (FIG. 2)
For dust blowing, attach the wind tube (1) to blower outlet, turning clockwise to lock it in place.
DUST SUCTION (FIG. 3)
- For dust suction, fit the wind tube (1) onto wind inlet (4) and dust bag (5) onto blower outlet.
- After the bag fills with dust, empty the contents of the dust bag into a dust bin by releasing the fastener.
OPERATION
CHARGING THE LI BATTERY PACK (FIG. 1A-1B)
- Remove the battery pack (6) from the handle, pressing the pushlock button (8) downwards to do so.
- Check that your mains voltage is the same as that marked on the rating plate of the battery charger. Insert the power plug of the charger (7) into the mains socket outlet. The green LED will be on.
- Push the battery pack onto the battery charger.
If the battery pack fails to charge, check for the following:
- voltage at the power socket
- whether there is good contact at the charging contacts of the charging unit
If the battery pack still fails to charge contact your nearest retailer.
To ensure that the Li battery pack provides long service you should take care
to recharge it promptly. You
must recharge the battery pack when you notice that the power of the cordless
equipment drops.
BATTERY CAPACITY INDICATOR (FIG. 1C)
Press the battery capacity indicator switch (a). The battery capacity
indicator (9) shows the charge status of the battery using 3 LEDs.
- All 3 LEDs are lit: The battery is fully charged.
- 2 or 1 LED(s) are lit: The battery has an adequate remaining charge.
SWITCH ACTION (FIG. 4)
CAUTION: Before inserting the battery into the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when released.
- When you start the tool, just press the trigger (a). When the trigger is released, the tool stops.
- The trigger can be locked in working positon. To lock the switch, press the trigger and then press down the locking lever (b), and then loosen the switch and loosen the locking lever(b), the trigger is locked and the tool stays in working status.
- To release the trigger from lock status, press the trigger again. The locking lever automatically bounces back and trigger can be released.
ADJUST AIR VOLUME (FIG. 4)
When the trigger is fully pressed, turning the rotary adjusting dial (c) can adjust the air volume.
ADJUST HANDLE ANGLE (FIG. 5)
- Press the angle adjust button (2), machine can turn at 90°. It will provide more convenience when using dust suction function.
- To turn the handle back, press the angle adjust button (2) again.
CLEANING AND MAINTENANCE
Always disconnect the plug from the socket before carrying out any cleaning work.
CLEANING
- Keep all air gaps and engine housing clean as far as possible.
- Wipe the device with a clean cloth or blow it with compressed air.
- We recommend cleaning the device every time it’s done.
- Clean the device regularly with a damp cloth and a small amount of soap. Do not use detergents or solvents that can damage the plastic parts of the device. Be careful that water does not get inside the device.
MAINTENANCE
Our machines have been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation depends upon proper
machine care and regular cleaning. Please charge the battery regularly, for
example, once every 6 months.
REPAIR
Only use accessories and spare parts recommended by the manufacturer.
If the device is damaged after a few days, despite our quality control and
your maintenance, only an authorized electrician can repair it.
ENVIRONMENT
Should your appliance need replacement after extended use, do not dispose of
it with the household refuse, but in an environmentally safe way.
Waste produced by electrical machine items should not be handled like normal
household rubbish. Please recycle where recycle facilities exist. Check you’re
your Local Authority or retailer for recycling advice.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>