BORMANN BLG4000 Table Gas Stove Cooker Instruction Manual

BORMANN BLG4000 Table Gas Stove Cooker

Safety Instructions

• Carefully read this instruction manual before start to use the product, install the gas pipe and/or connect the gas cylinder .
• The appliance is compliant with standard: EN 484: 1997.
• Well keep this instruction manual for future reference
• Only to be used outdoors . It is forbidden to use the equipment in houses.
• This appliance must be kept away from inflammable materials and heat source
• Never use the stove near heat sources, open flames and flammable materials .
• Place always the stove on perfectly horizontal surfaces and heat resistant . Never place the stove on surfaces in paper support, wood, plastic or any other flammable materials .
• Always verify that the product is undamaged before starting to use it . In the case are present any kind of damage , never use the appliance and get in contact only with the authorized service centre by the manufacturer.
• Do not modify or repair for any reason the equipment yourself or by unauthorized personnel . In case of malfunction or apparent damage, always contact the service centres authorized by the manufacturer .
• Do not use the appliance with damaged seals and/or in case of leaking due to wear of the components. Replace damaged hoses before using appliance.
• Do not use the stove for any others purposes than cooking food or heating up of liquids for food use.
• Never leave the appliance unattended during the use.
• Always keep the stove out of reach of children , out of dependent persons and pets .
• During the use , the stove could reach high temperatures . Pay always a lot of attention when your are using it and avoid to touch the metal parts when hot .
• Never move the device during use. Use protective glove when handling particularly hot components.
• Do not move the appliance during use.
• If you feel gas’s smell coming from the appliance , immediately turn off the stove and close the gas cylinder valve. Contact an authorized service centre to solve the problem.
• Use only and exclusively LPG gas cylinder and in accordance with legislation TPED
• Turn off the gas supply at the gas container after use.
• It shall be carried out away from any source of ignition when changing the gas container.
• The length of hose cannot exceed 1.5m. In Finland, the length of hose cannot exceed 1.2m.
• Make sure hose is not kinked. Make sure that when connected hose does not touch any warm surfaces.
• It’s necessary to change the flexible tube when the national conditions require it.
• Only regulator complies with EN 16129 can be used. Always use a low-pressure regulator to connect the gas cylinder to the stove. This regulator for I3+(28-30/37) must to have exclusively a fixed calibration normalized at 37 mbar for Propane and 30 mbar for Butane. For I3B/P(30), the regulator should have a fixed calibration normalized at 30mbar.
• To store the product always in dry and slightly moist places , away from the atmospheric agents or factors that could damage the stove itself.
• All repairs must be performed only by qualified personnel in the service centres authorized by the manufacturer or importer.
• Avoid to block the venturis of burners. Check whether the venturis of burners are blocked before using the appliances.
• The diameters of cooking vessels which can be used are 120mm~200mm.
• Parts sealed by the manufacturer or his agent must not be altered by the users.
• Any modification of the appliance may be dangerous.

Instructions of Use

• Carefully read this instruction manual before start to use the product, install the gas pipe and/or connect the gas cylinder.
• Attention: during the use, this equipment generates emissions of carbon dioxide, which could became dangerous if accumulated. For this reason, only use this product outdoor.
• It is forbidden to use the equipment in houses .

Installation

• Place the stove on a horizontal surface respecting the instructions indicated in the chapter of Safety Instruction. Please refer to the parts list and assembly diagram as necessary.
• Check that the gas pipe that you want to use is in accordance with the rules in force in your country and it has already assembled with the pressure reducer with the characteristics described in the chapter of Safety Instruction and in the technical data table.
• Insert into the gas pipe a full mesh metal clamp suitable for LPG gas pipes .
• To insert the gas pipe in the stove gas’s connector on the back of the stove and push it until the pipe is inserted up to the connector for at least 2cm .
• Tighten the metal clamp in order to seal safely the rubber hose to the stove connector.

LPG Cylinder Assembly

• Before assembling the cylinder, turn the burner valve’s knobs clockwise until them reach the closed position.
• Place the gas cylinder in a stable and dry surface
• Connect the pressure regulator already assembled to the gas pipe to the LPG cylinder making sure you have correctly inserted the seal gasket supplied with the cylinder.
• Always use the new gaskets supplied together with the LPG cylinder.
• Tighten the regulator to the cylinder to prevent gas leakage.
• Check that the gas hose is not twisting. In case, rotate the pipe in order that every twist or curve is eliminated and the tube has a linear shape.
• Turn the cylinder’s valve knob until fully open in order to allow the gas LPG to feed the stove.
• Keeping the stove taps closed for five minutes and check does not spread out smell of gas before proceeding with the use of the stove.
• To verify that the installation has been done successfully, pour soapy on the joints of every connection. Any leaking will be well visible using this solution.
• Attention: Never use a flame to check the Gas leaking.

Using the stove

• Lightly press and turn counter-clockwise the burner valve’s knob according the burner you want use.
• Put a lighter close to the defined burner
• Wait until the burner is fully switch ON and adjust the flame by turning the knob clockwise or counter-clockwise according your needs .
• To make the temporary shut-down of the burner , turn the knob clockwise to the OFF position.
• After cooking , or before storing the product, turn OFF the burner by turning clockwise the cylinder valve’s knob tilli s close and wait for the complete extinction of the flame . then rotate also the burner valve’s knob to OFF position. This eliminates residual gas inside the tube and in the stove as well .
• Wait until the stove is cold before moving or storing, at least 30 minutes.

LPG Cylinder Exchange

• If, while using, the burner goes OFF , needs to replace the cylinder .
• Turn OFF the cylinder and the burner’s knob to the close position before proceeding with the unscrewing of the pressure regulator.
• To assembly of a new Gas cylinder, please follow the instruction indicate in the chapter LPG gas cylinder assembling, always respecting the Safety Instructions .

Cleaning And Maintenance

• Regularly clean your Stove between uses and especially after extended periods of storage.
• Before proceeding with cleaning and maintenance of the product , make sure that the stove is properly cooled ; wait at least 30 minutes after the last use .
• Ensure that the cylinder valve and the burner’s valve are in the closed position . Remove the grid to perform the cleaning more conveniently .
• Use a damp sponge to remove heavier dirt , a damp cloth and then a dry cloth are enough to clean and dry all surfaces .
• Never use abrasive substances , solvents or flammable .
• The only maintenance required for this equipment are the gas pipe and the cylinder. Always make sure that these components are comply with current regulations and maintained in good working order . Always use the new gaskets supplied with the cylinder to ensure the seal between regulator and cylinder

Storage
Store your Stove in a cool dry place. Cover the burners with aluminum foil in order to prevent insects or other debris from collecting in burner holes. If the Stove is to be stored indoors, the gas cylinder must be disconnected and left outside. The gas cylinder should always be stored outside, in a dry, well-ventilated area, away from any sources of heat or ignition. Keep out of the reach of children.

Technical Data

Caution! The device must be connected to a 30 mbar low pressure regulator!

• The manufacturer reserves the right to make minor changes to product design and technical specifications without prior notice unless these changes signif-icantly affect the performance and safety of the products. The parts described / illustrated in the pages of the manual that you hold in your hands may also concern other models of the manufacturer’s product line with similar features and may not be included in the product you just acquired.
• Please note that our equipment has not been designed for use in commercial, trade or industrial applications. Our warranty will be voided if the machine is used in commercial, trade or industrial businesses or for equivalent purposes.
• To ensure the safety and reliability of the product and the warranty validity, all repair, inspection, repair or replacement work, including maintenance and special adjustments, must only be carried out by technicians of the authorized service department of the manufacturer.

WWW.BORMANNTOOLS.COM

PARTS NAMES

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>