BORMANN BAT6145 Paint Sprayer Gun Bottom Instruction Manual

BAT6145
055839
WWW.NIKOLAOUTOOLS.GR

SYMBOLS

| Read the manual before using the tool.
---|---
| Wear a dust mask.
| Wear safety glasses.
| Wear hearing protection.

SAFETY INSTRUCTIONS

Warning: Read the manual carefully before use. Failure to follow the warnings and instructions may result in injury and/or damage to property. Save the manual in a safe place for future reference.

• When sprayed, some materials produce toxic fumes, which can be harmful. Always wear safety glasses, gloves, respiratory protection, etc., to minimize the risk of personal injury caused by the inhalation of toxic fumes or from contact of solvents/paint with the skin or eyes.
• Never use oxygen, combustible gases or any other bottled gas to power the tool. This can cause serious injuries.
• Paint and solvents can be highly flammable. Only use in a well‐ventilated paint spraying booth. Avoid ignition sources (lighted cigarettes, naked flames, electrical sparks, etc.).
• Disconnect the air hose from the tool before performing maintenance and when the tool is not in use, to prevent it from being started accidentally. The installation of a ball valve on the compressed air line close to the spray gun is recommended.
• This tool is designed to operate on clean, dry, compressed air at regulated pressures between 3-4 bar.
• Only use parts, nozzles and accessories that are recommended by the manufacturer.
• Check that all screws and covers are fitted correctly and do not leak before using the tool.
• Check daily that the trigger and nozzle function correctly.
• Do not use solvents that contain homogenate hydrocarbons that can react chemically with elements of aluminium or zinc and cause an explosion.
• Never modify the product in any way.

SPECIFICATIONS

Technical Data

• The manufacturer reserves the right to make minor changes to product design and technical specifications without prior notice unless these changes significantly affect the performance and safety of the products. The parts described / illustrated in the pages of the manual that you hold in your hands may also concern other models of the manufacturer’s product line with similar features and may not be included in the product you just acquired.
• To ensure the safety and reliability of the product and the warranty validity, all repair, inspection, repair or replacement work, including maintenance and special adjustments, must only be carried out by technicians of the authorized service department of the manufacturer.
• Always use the product with the supplied equipment. Operation of the product with non-provided equipment may cause malfunctions or even serious injury or death. The manufacturer and the importer shall not be liable for injuries and damages resulting from the use of non-conforming equipment.

OPERATION

Using the spray gun (fig. 1)

•  This tool is designed to operate on clean, dry, compressed air at regulated pressures between 3.0-4.0 bar.
• Inspect the tool for damaged or worn parts and replace any damaged or worn parts.
• Make sure that the trigger and nozzle functions properly.
• Keep the tool at an appropriate distance from the workpiece. A suitable distance is 15-20 cm, depending on the air pressure and the task at hand.
• Hold the spray gun perpendicular to the workpiece and move it back and forth in parallel, horizontal lines.
• The trigger should be released before the spraying movement is ended.

1. Start moving the spray gun.
2. Squeeze the trigger.
3. Release the trigger.
4. Stop moving the spray gun.

Important: Too high or too low air pressure can damage the tool and give an unsatisfactory result. Adjustment
The desired pattern, volume of fluid output and fine spraying can easily be adjusted by regulating the pattern adjusting knob and fluid adjusting knob.
Adjusting the pattern: Turning the pattern adjusting knob to the right until tight will make the spray pattern round. Turning the knob left will make the spray pattern elliptical.
Adjusting the volume of fluid output: Turn the fluid adjusting knob clockwise to reduce the volume of fluid output and counter-clockwise to increase fluid output.

MAINTENANCE

1. Pour remaining paint into another container and clean the paint ducts and air cap. Spray a small amount of thinner to clean the paint ducts. Inadequate cleaning can cause incorrect patterns and also lead to particles entering the paint. Thoroughly clean the spray gun immediately after using two‐component paint.
2. Clean the other parts with the provided brush soaked in thinner and with a soft cloth.
3. Clean the paint ducts fully before dismantling the spray gun.
4. Remove the paint needle before removing the paint nozzle, otherwise the tool may be damaged.

Attention:

• Never spray foods or chemicals with the spray gun.
• Never pick at the nozzle or needle with metal wires or other hard objects. This will damage them.
• Never immerse the spray gun in solvent or other fluid. This will damage the air cap, paint nozzle and paint needle.
• Always clean all the parts before reassembling the tool.

TROUBLESHOOTING

Inconsistent flow of paint / the spray gun is making a hissing sound (”fluttering”)| 1. Material in container is dirty.
2. Dry or worn needle.
3. The paint nozzle is loose or worn.| 1. Add paint into the container.
2. Lubricate or replace the needle.
3. Tighten or replace the paint nozzle.
Arcing pattern of sprayed paint| 1. The paint nozzle is loose or worn.
2. Material build-up on the air cap.| 1. Tighten or replace the paint nozzle.
2. Remove obstructions from holes, keeping in mind not to use metal objects for this purpose.
Pattern is not evenly spread| 1. Material build-up on the air cap.
2. The paint nozzle is dirty or worn.| 1. Clean or replace the air cap.
2. Clean or replace the paint nozzle.
The center of pattern is too narrow| 1. The paint is too thin or not sufficient.
2. The air pressure is too high.| 1. Regulate the paint viscosity.
2. Reduce the air pressure.
The pattern width is not sufficient| 1. The paint is too thick.
2. The air pressure is too low.| 1. Regulate the paint viscosity.
2. Increase the air pressure.

WWW.NIKOLAOUTOOLS.GR

The pneumatic tools have been manufactured according to strict standards, set by our company, which are aligned with the respective european quality standards. The pneumatic tools are provided with a warranty period of 24 months for non-professional use and 12 months for professional use. The warranty is valid from the date of purchase of the product. Proof of the warranty right is the purchase document of the tool (retail receipt or invoice). Under no circumstances shall the company cover the relevant cost of spare parts and respective required working hours unless a copy of the purchase document is presented. In case the repair has to be done by our service department the cost of transportation (to and from) is entirely borne by the sender (client). Τhe said tools must be sent for repair to the company or to an authorized workshop in the appropriate way and means of transport.

WARRANTY EXEMPTIONS AND RESTRICTIONS:

1. Spare parts that wear out naturally as a consequence of being used (expendable parts).
2. Tools damaged as a result of non-compliance with the instructions of the manufacturer.
3. Tools poorly maintained or taken care of.
4. Use of improper lubricants or accessories.
5. Tools given to third entities free of charge.
6. Damage as a result of connection of pressurized air with a pressure that diff ers from the one required according to the technical data label.
7. Damage as a result of unclean, unfi ltered pressurized air use.
8. Damage or malfunction as a result of not cleaning the tool as required.
9. The tool has come in contact with chemicals, has been corroded or damaged by humidity.
10. Tools that have been modifi ed or disassembled by unauthorized personnel.
11. Tools used for rent.

The warranty covers only the free of charge replacement of the component that presents a manufacturing defect or material failure. In case of lack of a specifi c spare part the company reserves the right to replace the pneumatic tool with another of the same kind. After all warranty procedures have been concluded, the warranty period of the machine shall not be extended or renewed. Replacement of a spare part with repair charge is covered by a 1 year warranty of good operation, subject to compliance with the warranty terms. The spare parts or tools that are replaced remain in the possession of our company. Requirements, other than those mentioned in this warranty form, regarding repairing a tool or damage thereof, do not apply. Greek law and relative regulations apply to this warranty.

WARRANTY

This appliance is a quality product. It was designed in compliance with current technical standards and made carefully using normal, good quality materials. The warranty period is 24 months for non-professional use and 12 months for professional use and commences on the date of purchase, which can be verified by the receipt, invoice or delivery note. During this warranty period all functional errors, which, despite the careful treatment described in our operating manual, are verifi ably due to material flaws, will be rec fied by our after-sales service staff . The warranty takes the form that defec ve parts will be repaired or replaced with perfect parts free of charge at our discretion. Replaced parts will become our property. Repair work or the replacement of individual parts will not extend the warranty period not will it result in a new warranty period being commenced for the appliance. No separate warranty period will commence for spare parts that may be ted. We cannot offer a warranty for damage and defects on appliances or their parts caused by the use of excessive force, improper treatment and servicing. This also applies for failures to comply with the operating manual and the installation or spare and accessory parts that are not included in our range of products. In the event of interference with of modifications to the appliance by unauthorized persons, the warranty will be rendered void. Damages that are attributable to improper handling, over loading, or natural wear and tear are excluded from the guarantee. Damages caused by the
manufacturer or by a material defect will be corrected at no charge by repair or by providing spare parts. The prerequisite is that the equipment is handed over assembled, and complete with the proof of sale and guarantee. For a guarantee claim, only use the original packaging. That way, we can guarantee quick and smooth guarantee processing. Please send us the appliances post-paid or request a Freeway sticker. Unfortunately we will be unable to accept appliances that are not postpaid. The warranty does not cover parts that are subject to nat- ural wear and tear. If you wish to make a warranty claim, report faults or order spare parts or accessories, please contact the after- sales center: Subject to change without prior notice.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>