BORMANN BEM2000 1600W Double Beater Instruction Manual
- October 27, 2023
- BORMANN
Table of Contents
Instruction Manual
BEM2000
026761
BEM2000 1600W Double Beater
The manufacturer reserves the right to make minor changes to product
design and technical specifications without prior notice unless these changes
significantly affect the performance and safety of the products. The parts
described / illustrated in the pages of the manual that you hold in your hands
may also concern other models of the manufacturer’s product line with similar
features and may not be included in the product you just acquired.
Please note that our equipment has not been designed for use in
commercial, trade or industrial applications. Our warranty will be voided if
the machine is used in commercial, trade or industrial businesses or for
equivalent purposes.
***** To ensure the safety and reliability of the product and the warranty
validity, all repair, inspection, repair or replacement work, including
maintenance and special adjustments, must only be carried out by technicians
of the authorized service department of the manufacturer.
Please read and understand owner’s manual before operating the machine, keep
well the manual. Don’t operate the machine until you read the manual and
understand the operating and trouble shooting for the machine.
Safety instructions
Save all warnings and instructions for future reference. The term “power tool”
in the warnings refers to your mains-operated (corded) power tool or battery-
operated (cordless) power tool.
Work area safety
Keep work area clean and well lit. Cluttered or dark areas invite accidents.
Do not operate power tools in explosive atmospheres such as in the presence of
flammable liquids, gases or dust. Power tools create sparks which may ignite
the dust or fumes. Keep children and bystanders away while operating a power
tool. Distractions can cause you to lose control.
Electric safety
a) Power tool plugs must match the outlet. Never modify the plug in any way.
Do not use any adapter plugs with earthed (grounded) power tools. Unmodified
plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces, such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the ri electric
shock. If operating a power tool in a damp location is 1.1 use a residual
current device (RCD) protected supply. Use of an RCD reduces the risk of
electric shock.
NOTE: The term “residual current device (R the term “ground fault circuit
interrupter (GFCI)” or “earth leakage circuit breaker (ELC8)”.
Personal safety
- Stay alert, watch what you are doing and use c of drugs, alcohol or medication. A moment of Matte
- Use personal protective equipment. Always wear eye don used for appropriate condition will reduce personal inj es.
- Prevent unintentional starting. Ensure the switch is in the off zitlon before corn
- Carrying power tools with your finger on the switch or energizing power tools
- Remove any adjusting key or wrench before turning the power took onr personal injury.
- Do not overreach. Keep proper footing and balance at all times.
- This enables better control of the power tool in unexpected situations.
- Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothingan be caught in moving parts.
- If devices are provided for the connection of dust extraction and col – facilites, e iiibat can reduce dust-related hazards. ling a power tool. Do not use a power tool while you are tired or under the influence rug glower tools may result in serious personal injury. .ve equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protec. g to power source and/ or battery pack, picking up or carrying the tool. the switch on invites accidents. left attached to a rotating part of the power tool may result in rig pans. Loose clothes, jewellery or long hair can
Power tool use and care
- Do not force the power tool. Use the correct power tool for your application. The correct pow which it was designed.
- Do not use the power tool if the switch cannot turn on or off properly. Any power tool that cannot repaired
- Disconnect the plug from the power source and / or the battery pack from the power tool before making a
- ustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
- Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
- Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s opera-tion. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
- Keep cutting tools sharp and clean.
- Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
- Use the power tool, accessories and tool bits etc., in accordance with these instructions, taking into account the working conditions and the work to be per-formed. Use of the power tool for operations different from those intended could result in a hazardous situation. and properly used. Use of dust collection tter and more safely at the rate for led h the switch is dangerous and must be
Service
Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power
tool is maintained.
Additional safety instructions
- DO check the safety situation when the machine is in operating!
- DO operate the machine in the suitable working space!
- DO keep other persons away from the working space!
- DO avoid the machine affected with damp when the machine operated in the amp working space!
- DO keep the working space sufficient lighting!
- DO check the power source/voltage is same as showed on the machine label’s!
- DO check the machine have earth protecting or not!
- The machine CANNOT be over loading!
- The electrical cable CANNOT be too far away the machine, CANNOT pull the cable to disconnect the plug from the socket directly! Keep the cable from heating, damp, scratch!
- DO only use no scratch,no defected cable with plug!
- DO pull off the power source when the machine is out of work, maintenance or changing the mixing operation!
- DO NOT mix the material which flammable pointless than 21°C .
- DO NOT use solvents for cleaning the tools! Unless it will have explosion dangerous!
- DO NOT install and operator the machine in the flammable and explosive circumstance! Unless it will have explosion dangerous!
- DO NOT use the slide or movable mixing drum!
- DO NOT star the mixer until the mixing tools is in the mixing drum or other drums!
- DO NOT run idle of the machine!
- DO NOT take out the sample until the machine is stopped! DO NOT touch into the mixing drum when the machine is in operation!
- DO NOT star the machine when the dried materials is in the drum or stick to the drum!
- The machine will not be failure only you operate it carefully!
- Please wear goggle and ear cap when operating the machine!
- DO use only original spare parts for the machine maintenance!
Technical Data
| Voltage/frequency: | 230v/501-Iz |
|---|---|
| Power: | 1600W |
| Speed: | 1: 0-610RPM, 2:0-820RPM |
| Mixing paddle : | 110mm*570mm |
| Tool connection: | M14 |
| Additional features: | •Dual mechanical speed control |
•6 Position speed control
Description of main parts (picture A)
- Mixing Tool (P1 Paddle)
- Lock Clip Connection Shaft
- Electronic speed regulator
- 1 – 2 Speed Switching Poker Rod
- ON/OFF Switch (Trigger)
- Motor Housing
- Switch rest-lock knob *(equipped on the left or the right side, depending on the model)
Proper use
The mixer is a electrical power mixer, which fitted with double count-rotating
mixing tool. It is used for mixing building materials and chemical materials,
for mixing even heavy materials quickly and thoroughly.
Operating instructions
Mixing tools
For the mixer with double counter-rotating tools, we supply P1 mixing tool as
standard fitting.
P1: heavy duty, multifunction, suitable for heavy viscous materials, mortar,
quartz sand, heat proof paints etc.,it is also suitable for thin
materials
Picture 1: Make mixing tool’s groove(L) irect to the spline shaft(L) and put
into the spline shaft.
Picture 2: Tighten the mixing tools con- nected to the spline shaft by wrench.
Picture 3: the other mixing tools(R) is the same.
Quick coupling (not available with all models)
Picture 4: Pull the sleeve down 5-7mm, put the paddle to the Shaft.
The same action another one.
Picture 5: The Sleeve will be recoiled to the position. So the paddle was
Tightened.
Noticed: You can interchange the two paddle (Right Left ) for different liquid
direction.
Starting the machine
Push down the switch rest-lock knob first and then push down the start switch.
Mechanical speed regulator operation instruction:
A. When the machine IS under STOP condition, please turn the Knob switch to
change the speed;
B. When you can not finish changing speed completely by turn the Knob switch,
please turn the shaft paddles slightly and change speed.
Electronic speed regulator operation instruction:
Turn on the power switch first, then turn the regulator switch which located
in the left handle in order to select the speed.
Stopping the machine
Loose the start switch so the machine will be stopped.
Maintenance
Correct maintenance for the machine can prolong the working life; The handle
switch must always keep in proper function and good maintenance;
The mixing tools should be cleaned when the operation is finish or no use for
long time; Normally the flowing water or quartz sand can clean the mixing
tools well. Do not fore any mechanical stress in the machine, such as POUND,
because it will be unavoidable damaged;
The mixing shaft must
always be anti-pollution;
The hole of hexagonal socket must always be put protecting cover;
The vent of motor housing can not be covered when the machine is in operation,
there can not be any flammable materials in the machine;
The vent must be often cleaned;
Only original parts can used in this machine.
The carbon brush must be checked and maintenance when the machine operation up
to 60 hours, please change the brush in time if find the brush worn out. The
operation details see the pictures.
Picture 6: Cut off the power first and take apart the motor hosing.
Picture 7: Pull out the plate,replace the carbon brush.
Documents / Resources
|
BORMANN BEM2000 1600W Double
Beater
[pdf] Instruction Manual
BEM2000, 1600W Double Beater, BEM2000 1600W Double Beater, Double Beater,
Beater
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>