BORMANN BMS6500 Multi Purpose Grinder Instruction Manual

BMS6500 Multi Purpose Grinder
Instruction Manualwww.nikolaoutools.gr

BMS6500 Multi Purpose Grinder

Operating Instructions

NOTE: Before using the tool, read the instruction book carefully. This multi sharpener tool includes three working modules: HSS drill sharpener — Sharpens all high speed steel drill bits from 3 mm to 10mm.Knife & Scissor Sharpener — Sharpens all straight edged knives & scissors. Chisel & plane sharpener — Regrinds chisel & plane blades up to 51mm wide.
1. Switching on and off (see A)
WARNING! This electric multi-sharpener shall be fixed on the stable position before using.
To switch on, move the on/off switch (11) to the “I”position.
To switch off, move the on/off switch to the “O” position.
2. Sharpening HSS bits
WARNING! Before assembling the HSS drill sharpener (2), be sure the tool is unplugged and the on/off switch (11) is in “O’’ position.

1. Slide the module labeled High Speed Steel Drill Sharpener onto the power unit. (SEE B1,B2)
2. Remove the clamp (3) from the clamp holder and insert the HSS drill bit (4) to be sharpened. Rotate the clamping ring (5) in clockwise direction to tighten the clamp lightly to leave the drill bit still free to move. (SEE C1, C2)
3. Place the clamp containing your drill bit into the setting slot (6), using the grooves in the side to lower it in correctly. (SEE D1, D2)
4. Move the drill bit forward up so that it lays in the “V” guide and touches the metal end stop.(SEE E)
5. Turn the drill bit until the V guide fully drops over it. All four drill bit corners should now be touching the V guide sides. (SEE E)
6. Ensure that the drill and holder are fully down in the setting slot. With the drill bit in this position, tighten the clamping ring in clockwise direction. (SEE E)
7. Lift up the “V” guide and remove the clamp and drill bit. (SEE F)
8. Transfer the clamp and drill bit into the clamp holder. (SEE G)
9. Switch the power unit on. (SEE A)
10. Move the clamp holder from side to side as indicated by the arrow on the sharpener, securing with light finger pressure. (SEE H)
11. Remove drill bit and clamp and turn over (SEE I).Repeat Step 10.
12. Check the leading edge of both flutes are equally sharp. They should meet exactly in the middle as in J1, not J2.
13. Switch the power unit off. Before removing the module, ensure the grinding wheel has stopped.

Important note!

1. When sharpening HSS drill bits Ø3.5mm toØ10mm(not includingØ3.5mm)(SEE J3),make the stepped surface (a) upward, and make the plane face the HSS drill bits.
2. When sharpening HSS drill bits of Ø3mm toØ3.5mm ( includingØ3.5mm) (SEE J4), loose the clamping ring, then turn around the clamping ring and the clamp with 1800 which show the stepped surface (a) downward. In other words, make the stepped face the drill bits.
3. Make sure the length of the HSS drill bits in sharpening is more than 70mm.

3. Sharpening knives
WARNING! Before assembling the knife&scissor sharpener(8), be sure the tool is unplugged and the on/off switch (11) is in “O’’ position.
NOTE: This module is suitable for all straight edged, household knives and scissors only.
Do not use serrated edged blades.

1. Slide module labeled Knife & Scissor Sharpener (8) on to the power unit.
2. Switch the power unit on.
3. Hold the knife handle towards you and insert the handle end of the blade into knife sharpening slot(10). (SEE K)
4. As soon as the blade touches the grinding wheel, draw it with light steady pressure across the wheel to the tip, then remove. Do not press hard.
5. Insert the second side of the blade into the other top guide slot and repeat step 4. (SEE L)
6. Repeat sharpening each side in turn until a clean sharp edge is attained.
7. Switch the power unit off. Before removing the module, ensure that the grinding wheel has stopped.

4. Sharpening scissors
WARNING! Before assembling the knife&scissor sharpener(8),be sure the tool is unplugged and the on/off switch (11) is in ‘’O’’ position.
NOTE: This module is suitable for all straight edged, household knives and scissors only.
Do not use serrated edged blades.

1. Slide module labeled Knife & Scissor Sharpener (8)onto the power unit.
2. Switch the power unit on.
3. Open the scissors fully.
4. Slide the first scissor blade through the scissor sharpening slot.Keep the pivot of the scissors and other blade to right hand side. (SEE M)
5. Draw the blade across the grinding wheel from pivot to tip. Use a light steady pressure, do not press too hard.
6. Remove and turn scissors over to sharpen the second blade. Keep the pivot to the right and sharpen from pivot to tip. (SEE N)
7. Repeat if necessary, until clean sharp edges are achieved.
8. Switch the power unit off. Before removing the module, ensure that the grinding wheel has stopped.

5. Sharpening Chisel & Plane Blades
WARNING! Before assembling the chisel&plane sharpener(12), be sure the tool is unplugged and the on/off switch (11) is in ‘’O’’ position.

1. Slide the module labeled Chisel & Plane Sharpener(12) onto the power unit.
2. Place the blade against the back lip of the plate. The magnet(13) helps to hold it in place.(See O)
3. The sharpening angle must match the existing bevelled angle on the blade tip. Adjust, if necessary.
4. To alter the angle:
5. Loosen the angle adjusting knob (15) in anti-clockwise direction.
6. Adjust the plate. The sharpening angle is indicated by the small arrow. The adjustable grinding angle is from 20° to 40°.Make sure the blade edge touches the grinding wheel.
7. Tighten the angle adjusting knob. (See P)
8. Switch the power unit on.
9. Slide the blade and plate with light steady pressure back and forth across the grinding wheel in a continuous motion. Do not hold the blade stationary. This causes irregular sharpening. (See Q)
10. Gradually adjust the blade down the plate while sharpening (See R). Do not press hard. Grind gradually, repeating the step.
11. Remove the blade and make sure the bevelled edge and tip are evenly sharp. If not, adjust the grinding angle. It is important that the sharpening angle matches the existing bevelled angle of the blade. This avoids removing too much metal unnecessarily and keeps plane blades at their optimum shaving angle.(See S)
12. When sharpening thin chisel blades, place the small chisel guide onto the plate to act as a spacer and sharpen as before. (See T)
13. Switch the power unit off. Before removing the module, ensure the grinding wheel has stopped.
14. Recommend that after grinding, the blade tip is honed on an oil stone.

6. Drive shaft

1. To fit the drive shaft, remove the cap from the drive shaft connector and screw the inner end of the shaft onto the threaded connector.
2. The outer end of the drive shaft is fitted with a collet. To loosen the collet, lock the drive shaft with the locking pin and unscrew the retainer with the spanner provided.
3. Insert the shaft of the tool to be used into the collet and re-tighten.

Maintenance

Remove the plug from the socket before carrying out any adjustment, servicing or maintenance.
Your power tool requires no additional lubrication or maintenance.
There are no user serviceable parts in your power tool. Never use water or chemical cleaners to clean your power tool. Wipe clean with a dry cloth. Always store your power tool in a dry place. Keep the motor ventilation slots clean. Keep all working controls free of dust. Occasionally you may see sparks through the ventilation slots. This is normal and will not damage your power tool.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

SPECIFICATIONS

Technical Data

• The manufacturer reserves the right to make minor changes to product design and technical specifications without prior notice unless these changes significantly affect the performance and safety of the products. The parts described / illustrated in the pages of the manual that you hold in your hands may also concern other models of the manufacturer’s product line with similar features and may not be included in the product you just acquired.
• To ensure the safety and reliability of the product and the warranty validity, all repair, inspection, repair or replacement work, including maintenance and special adjustments, must only be carried out by technicians of the authorized service department of the manufacturer.
• Always use the product with the supplied equipment. Operation of the product with non-provided equipment may cause malfunctions or even serious injury or death. The manufacturer and the importer shall not be liable for injuries and damages resulting from the use of non-conforming equipment.

ENVIRONMENTAL DISPOSAL

In order to avoid damages on transportation, the tool has to be delivered in solid packaging. Packaging as well as the unit and accessories are made of recyclable materials and can be disposed accordingly. The tool’s plastics components are marked according to their material, which makes it possible to remove environmental friendly and differentiated because of available collection facilities.
Only for EU countries
Do not dispose of electric tools together with household waste material!
In observance of European Directive 2002/96/EC on waste electrical and electronic equipment and its implementation in accordance with national law, electric tools that have reached the end of their life must be collected separately and returned to an  environmentally compatible recycling facility.
WWW.NIKOLAOUTOOLS.GR

WARRANTY

The power tools have been manufactured according to strict standards, set by our company, which are aligned with the respective European quality standards. The power tools of our company are provided with a warranty period of 24 months for non-rofessional use, 12 months for professional use and 6 months for batteries. The warranty is valid from the date of purchase of the product. Proof of the warranty right is the purchase document of the tool (retail receipt or invoice). Under no circumstances shall the company cover the relevant cost of spare parts and respective required working hours unless a copy of the purchase document is presented. In case the repair has to be done by our service department the cost of transportation (to and from) is entirely borne by the sender (client). The tools must be sent for repair to the company or to an authorized workshop in the appropriate way and means of transport.
WARRANTY EXEMPTIONS AND RESTRICTIONS:

1. Spare parts that wear out naturally as a consequence of being used (brushes, cables, switches, chargers, chokes etc.).
2. Tools damaged as a result of non-compliance with the instructions of the manufacturer.
3. Tools poorly maintained.
4. Use of improper lubricants or accessories.
5. Tools given to third entities free of charge.
6. Damage due to an electrical connection at a voltage other than that indicated on the appliance plate.
7. Connection to a non-earthed power supply.
8. Change in current voltage.
9. Damage resultong from the use of salty water (e.g., washing machines, pumps).
10. Damage or malfunction resulting from improper cleaning procedure of the tool.
11. Contact of the tool with chemicals, or damage as a result of moisture or corrosion.
12. Tools that have been modifi ed or opened by unauthorized personnel.
13. Tools used for rent.

The warranty covers only the free of charge replacement of the component that presents a manufacturing defect or material failure. In case of lack of a specifi c spare part the company reserves the right to replace the tool with another corresponding model. After all warranty procedures have been concluded, the warranty period of the tool shall not be extended or renewed. Replacement of a spare part with repair charge is covered by a 1 year warranty of good operation, subject to compliance with the warranty terms. The spare parts or tools that are replaced remain in the possession of our company. Requirements, other than those mentioned in this warranty form, regarding power tools repair or damage thereof, do not apply. Greek law and relative regulations apply to this warranty.
WARRANTY
This appliance is a quality product. It was designed in compliance with current technical standards and made carefully using normal, good quality materials. The warranty period is 24 months for non-professional use and 12 months for professional use and commences on the date of purchase, which can be verified by the receipt, invoice or delivery note. During this warranty period all functional errors, which, despite the careful treatment described in our operatoing manual, are verifi ably due to material flaws, will be rectified by our aft ersales service staff . The warranty takes the form that defective parts will be repaired or replaced with perfect parts free of charge at our discretion. Replaced parts will become our property. Repair work or the replacement of individual parts will not extend the warranty period not will it result in a new warranty period being commenced for the appliance. No separate warranty period will commence for spare parts that may be ted. We cannot off er a warranty for damage and defects on appliances or their parts caused by the use of excessive force, improper treatment and servicing. This also applies for failures to comply with the operating manual and the installation or spare and accessory parts that are not included in our range of products. In the event of interference with of modifi cations to the appliance by unauthorized persons, the warranty will be rendered void. Damages that are atiributable to improper handling, over loading, or natural wear and tear are excluded from the guarantee. Damages  caused by the manufacturer or by a material defect will be corrected at no charge by repair or by providing spare parts. The prerequisite is that the equipment is handed over assembled, and complete with the proof of sale and guarantee. For a guarantee claim, only use the original packaging. That way, we can guarantee quick and smooth guarantee processing. Please send us the appliances post-paid or request a Freeway sticker. Unfortunately we will be unable to accept appliances that are not postpaid. The warranty does not cover parts that are subject to natural wear and tear. If you wish to make a warranty claim, report faults or order spare parts or accessories, please contact the after-sales center: Subject to change without prior notice.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>