lionelo Neal Baby Car Seat User Manual
- June 9, 2024
- lionelo
Table of Contents
Neal Baby Car Seat User Manual
Neal Baby Car Seat
Dear Customer!
Before you use the car seat for the first time, please read this operating
manual carefully.
Should you have any remarks or questions concerning the product, please do not
hesitate to contact us: help@lionelo.com
The product complies with the following standards: R129/03
Producer:
BrandLine Group Sp. z o. o. ul. A. Kręglewskiego 1, 61-248 Poznań, Poland
Important
Please read this manual carefully before you start installing the product and
remember to keep it for future reference. A wrong installation may pose a
threat to child’s health.
Notice
This is a i-Size booster seat Enhanced Child Restraint System. It is approved
according to UN Regulation No. 129, for use primarily in “ i-Size seating
positions” as indicated by vehicle manufacturers in the vehicle user’s manual.
If in doubt, consult either the Enhanced Child Restraint System manufacturer
or the retailer.
-
This product is intended for children whose height ranges from 100 to 150 cm (aged 4-12), while weight from 15 to 36 kg.
This product may not fit some vehicles in case your child’s height is 135-150 cm. -
Hard components and plastic parts of the child restraint systemmust be placed and installed in a way that they are not trapped by sliding seat or vehicle door under normal conditions of use.
-
All belts which secure the car seat must be tight and adapted to child’s body. The belts must not be twisted.
-
All hip belts must go low so that the child’s pelvis is held properly.
-
The product must be replaced if it has been exposed to overloads in case of accident.
-
Do not make any modifications or supplementation to the product. Please strictly follow the operating manual.
-
Make sure the product is not exposed to direct sunlight. It may cause the product to heat up and, in effect, burn the child’s skin.
-
Do not leave the child in the car seat unattended.
-
Luggage and other items which may cause bodily injuries in case of car collision must be properly secured.
-
Do not use the child safety seat without its fabric cover. Do not replace the cover with other than recommended by the manufacturer. The cover is an integral part of the car seat.
-
Buckle correctly and properly. In case of emergency, proper protection of buckles lets you take the child out of the car seat easily.
-
Before you install the car seat, please read the vehicle manual too.
PRODUCT OUTLINE (fig. 1)
- Adjustable headrest
- Headrest adjustment
- Shoulder belt guide
- Hip belt guide
- Car seat base
- Inclination adjustment lever
- ISOFIX arms
- ISOFIX release key
- ISOFIX control light
- ISOFIX fastening spots
HOW TO INSTALL
If the car seat cannot be installed with the use of ISOFIX fastening spots in
the vehicle, ISOFIX fasteners may remain hidden inside the car seat, and the
car seat may be therefore installed solely with the use of threepoint safety
belts.
By installing the child safety seat on the front seat of the vehicle, make
sure the backrest of the vehicle seat is in vertical position.
With three-point safety belts and ISOFIX fasteners
- Place the child safety seat inside the car. Grip and pull ISOFIX release key to pull ISOFIX arms out (fig. 2). ISOFIX arms work properly when you pull them out fully.
- Press ISOFIX fasteners against ISOFIX fastening spots in the vehicle (fig. 3). Make sure all ISOFIX control lights are GREEN (fig. 4). Press the child restraint system against the vehicle seat backrest as much as you can.
- Put the child in the car seat.
- Carry the shoulder belt through the shoulder belt guide (fig. 5). Carry the hip belt through the hip belt guide (fig. 9). Fasten safety belts. Make sure the belt is not twisted (fig. 9A).
With three-point safety belts only
Place the child safety seat on the vehicle seat. Carry the shoulder belt
through shoulder belt guide (fig. 5). Carry the hip belt through hip belt
guide (fig. 9). Fasten safety belts. Make sure the belt is not twisted (fig.
9A).
How to put the child in
- Adjust the headrest to child’s height by pressing the height adjustment (fig. 6). Adjust the headrest so that there is a fingerthick space between the headrest and child’s arms (fig. 7).
- The car seat can be inclined in three positions. Set the car seat in a suitable position before you secure the child with safety belts (fig. 8).
- Fasten safety belts (fig. 9). Make sure the belt is not twisted (fig. 9A).
How to take the car seat out
- Remove the shoulder belt from the shoulder belt guide and hip belt from the hip belt guide (fig. 10).
- Press ISOFIX release key to release and retract ISOFIX fasteners (fig. 11).
- Take the car seat out of the vehicle.
How to remove fabric cover and put it back on
- The fabric cover is mounted with the use of elastic hooks.
- When you wish to remove the cover, start from car seat backrest cover.
HOW TO MAINTAIN AND CLEAN
- Wash mechanically the fabric cover at the temperature of 30°C.
- Do not dry mechanically.
The pictures are for reference only. The real design of the products may differ from the pictures presented.
Detailed warranty conditions are available on the website:
www.lionelo.com
Documents / Resources
|
lionelo Neal Baby Car
Seat
[pdf] User Manual
Neal Baby Car Seat, Neal, Baby Car Seat, Car Seat, Seat
---|---
|
lionelo Neal Baby Car
Seat
[pdf] User Manual
Neal Baby Car Seat, Neal, Baby Car Seat, Car Seat
|
lionelo Neal Baby Car
Seat
[pdf] User Manual
Neal Baby Car Seat, Neal, Baby Car Seat, Car Seat, Seat