SUPER BRIGHT LEDS MCB-RGB-DC99 Color Chasing RGB LED Controller with Remote User Manual

: June 9, 2024
: super bright leds

Table of Contents

SUPER BRIGHT LEDS MCB-RGB-DC99 Color Chasing RGB LED Controller with
Parts Included
Remote Functions
Remote Pairing Options
Controller Installation
FCC Statement
Static Programs
Specification
Dynamic Programs
- References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SUPER BRIGHT LED

SUPER BRIGHT LEDS MCB-RGB-DC99 Color Chasing RGB LED Controller with

Remote User Manual

Part Number: MCB-RGB-DC99

Important: Read all instructions prior to installation.

Parts Included

1 – LED Controller
1 – Wireless Remote
1 – CR2025 3V Battery

Remote Functions

FIG 1 Remote Functions

Power Input
The power supply input.
The DC jack’s inner pin is positive and outer contact is negative.
Signal Output
Black / Ground,
Green / Clock
Red / Data
Blue / 12V+
Mode Adjust
Selects running mode.
Advance to next mode by pressing ‘MODE+’ or advance to previous mode by pressing ‘MODE-’.
Speed (Brightness) Adjust
Sets running speed of a dynamic mode or brightness of a static color. There are 10 different levels for both speed and brightness.
Pause / Play
Toggles between Play and Pause modes. Button will also release pause mode and start to play if running mode is changed.
Turn On / Standby
Turns on or switches to standby mode. Main unit will memorize current setting. When power is restored to the unit, it will automatically restore to previous state.
Unit Length (Static Color) Adjust
Adjusts playing unit length during dynamic modes or adjusts color during static color modes. On static color mode, press these keys to access one of 29 preset colors.
Program direct selection keys
User can directly select a program by the Enter and Number keys. For example, if you want to run program #58, press number 5 and then 8. Press Enter key to send the command.
Static Color Mode
User can directly select a static color by pressing 0, 0 then Enter. Use the Length (+) / Length (-) to select color.
Demo Mode
Switch to demo mode. In demo mode, the controller will automatically cycle through 99 dynamic programs.
Remote Controller indicator
The blue indicator will light up when remote controller is sending a command. When directly selecting a pattern with the 0-9 buttons, the blue indicator will flash up to seven times before the last key input is ignored. All digits and enter need to be input with no more than 7 seconds between button presses.

Remote Pairing Options

Controller and remote are 1 to 1 paired as default. Controller can only be controlled by a paired remote. When an extra remote is needed or the controller needs to be matched to another remote, the user can match the remote by following the instructions below.

Pairing a New Remote
Unplug controller power and plug in again after waiting 10 seconds. Press the ‘MODE-’ and ‘LENGTH-’ keys at same time once within 5 seconds after the power is on, then release the keys and press the ‘SPEED+’ key once within another 5 seconds. The controller can be paired to maximum 5 remotes.

Pairing to Any Remote
Unplug the controller power and plug in again after 10 seconds. Press the ‘MODE-’ and ‘LENGTH-’ keys at same time once within 5 seconds after power is on, then release the keys and press the ‘DEMO’ key once within another 5 seconds.

Pairing to One Remote
Unplug controller power and plug in again after 10 seconds. Press the ‘MODE-’ and ‘LENGTH-’ keys at the same time once within 5 seconds after power is on, then release the keys and press ‘SPEED-’ key once within another 5 seconds.

Controller Installation

Pre-test LED Configure
Remove strip from the reel and make connections to the controller and power supply (see “Method 1” diagram). Turn on the strip using the included remote control to ensure proper operation of the strip, controller, power supply, and remote.

See Method 1 diagram for a guide to installing and connecting LED strip to included controller and power supply for your application. Choose a suitable location for the power supply and controller. Direct line of sight is not required with RF remote control.

Power Supply
The power supply jack is a 5.5mm diameter DC socket. The main unit can work at DC 5V to 24V. Since the power supply is directly connected to the LED signal output, make sure the power voltage matches the LED strip requirement, incorrect voltage may damage LED strip.

Output Signal
The output signal is from an LC4 type plug. LEDs may not work properly if the data cable is too long or gets interfered with. Max run is 50 meters or 10 strips.

Connection Method 1 (Single 5m Strip)

Connections Method 2 (Multiple 5m Strip)

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.