BUFFALO DB455 Food Warmer Instruction Manual

: June 8, 2024
: BUFFALO

Table of Contents

Safety Instructions
Introduction
Pack Contents
Operation
Cleaning, Care & Maintenance
Troubleshooting
Technical Specifications
Electrical Wiring
Compliance
DECLARATION OF CONFORMITY
Coustamer Support
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

**BUFFALO DB455 Food Warmer Instruction Manual

**

Safety Instructions

Position on a flat, stable surface.
A service agent/qualified technician should carry out installation and any repairs if required. Do not remove any components on this product.
Consult Local and National Standards to comply with the following:
- Health and Safety at Work Legislation
- BS EN Codes of Practice
- Fire Precautions
- IEE Wiring Regulations
- Building Regulations
DO NOT immerse the appliance in water.
DO NOT touch the top of the appliance when in use. Surfaces are hot!
DO NOT store items on the top of the appliance.
DO NOT obstruct or cover the appliance in any way when in use.
DO NOT use an extension cable to power the appliance.
Always switch off and disconnect the power supply to the appliance when not in use.
Keep all packaging away from children. Dispose of the packaging in accordance to the regulations of local authorities.
If the power cord is damaged, it must be replaced by a BUFFALO agent or a recommended qualified technician inorder to avoid a hazard.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience or knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
BUFFALO recommend that this appliance should be periodically tested (at least annually) by a Competent Person. Testing should include, but not be limited to: Visual Inspection, Polarity Test, Earth Continuity, Insulation Continuity and Functional Testing.
BUFFALO recommend that this product is connected to a circuit protected by an appropriate RCD (Residual Current Device).

Introduction

Please take a few moments to carefully read through this manual. Correct maintenance and operation of this machine will provide the best possible performance from your BUFFALO product.

Pack Contents

The following is included:

BUFFALO Carving Station Food Warmer
Instruction Manual

BUFFALO prides itself on quality and service, ensuring that at the time of packaging the contents are supplied fully functional and free of damage.
Should you find any damage as a result of transit, please contact your BUFFALO dealer immediately

Operation

Turn the appliance On/Off using the power switch on the stem of the appliance.

Note: The appliance only maintains temperature, it does NOT continue to cook
food

Cleaning, Care & Maintenance

A BUFFALO dealer or qualified technician should carry out repairs if required.
Always switch off the appliance, disconnect the power supply and allow to cool before cleaning or performing maintenance.

Troubleshooting

Fault	Probable Cause	Solution
The unit is not working	The unit is not switched on	Check the unit is

plugged in correctly and switched on
Plug or lead is damaged| Call BUFFALO agent or qualified Technician
Fuse in the plug has blown| Replace the fuse
Power supply| Check power supply
Lamp expired| Replace lamp, part number AE307 or AG570

Technical Specifications

Model| Voltage| Power| Current| Dimensions (H x W x D mm)| Weight
---|---|---|---|---|---
DB455| 220-240V~50Hz| 250W| 1A| 670 x 180 x 260| 6kg

Electrical Wiring

This appliance is supplied with a 3 pin BS1363 plug and lead. The plug is to be connected to a suitable mains socket. BUFFALO appliances are wired as follows:This appliance is supplied with a 3 pin BS1363 plug and lead. The plug is to be connected to a suitable mains socket.
BUFFALO appliances are wired as follows:

Live wire (coloured brown) to terminal marked L
Neutral wire (coloured blue) to terminal marked N
Earth wire (coloured green/yellow) to terminal marked E

This appliance must be earthed.

Electrical isolation points must be kept clear of any obstructions. In the event of any emergency disconnection being required they must be readily accessible.

Compliance

The WEEE logo on this product or its documentation indicates that the product must
not be disposed of as household waste. To help prevent possible harm to human health and/or the environment, the product must be disposed of in an approved and environmentally safe recycling process. For further information on how to dispose of this product correctly, contact the product supplier, or the local authority responsible for waste disposal in your area.

BUFFALO parts have undergone strict product testing in order to comply with regulatory standards and specifications set by international, independent, and federal authorities.

Symbols
BUFFALO products have been approved to carry the following symbol:

DECLARATION OF CONFORMITY

Equipment Type • Uitrustingstype • Type d’équipement • Gerätetyp• Tipo di apparecchiatura • Tipo de equipo • Tipo de equipamento| Model • Modèle • Modell • Modello• Modelo • Malli
---|---
Carving Station Heat Lamp| DB455 (& -E)
Application of Territory Legislation & Council Directives(s)Toepassing van Europese Richtlijn(en)• Application de la/des directive(s) du Conseil • Anwendbare EU-Richtlinie(n)• Applicazione delle Direttive• Aplicación de la(s) directiva(s) del consejo • Aplicação de directiva(s) do Conselho| Low Voltage Directive (LVD) – 2014/35/EU Electrical Equipment (Safety) Regulations 2016 EN 60335-1:2012 +A11:2014+A13:2017 +A1:2019 +A2:2019 +A14:2019 EN 62233:2008 **Electro- Magnetic Compatibility (EMC) Directive 2014/30/EU – recast of 2004/108/EC Electromagnetic Compatibility Regulations 2016 (S.I. 2016/1091) EN IEC 55015:2019 +A11:2020 EN IEC 61000-3-2:2019EN 61000-3-3:2013 +A1:2019EN 61547:2009 ****Restriction of Hazardous Substances Directive (RoHS) 2015/863 amending Annex II to Directive 2011/65/EU Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012 (S.I. 2012/3032)
Producer Name • Naam fabrikant • Nom du producteur • Name des Herstellers• Nome del produttore • Nombre del fabricante • Nome do fabricante| Buffalo**

I, the undersigned, hereby declare that the equipment specified above conforms to the above Territory Legislation, Directive(s) and Standard(s).

11 th Augus t 2021

Coustamer Support

UK	+44 (0)845 146 2887

Eire
NL| 040 – 2628080
FR| 01 60 34 28 80
BE-NL| 0800-29129
BE-FR| 0800-29229
DE| 0800 – 1860806
IT| N/A
ES| 901-100 133
PT| vendas@nisbets.pt