GE Lighting MN2S-300/6FC String A Long 300 Count Constant Clear Mini Incandescent Plug In Christmas Icicle Lights Instructions
- June 8, 2024
- GE Lighting
Table of Contents
Model No.MN2S-300/6FC(0.6)
Instructions
MN2S-300/6FC String A Long 300 Count Constant Clear Mini Incandescent
Plug In Christmas Icicle Lights
a) When using electric products basic precautions should always be followed
including the following:
b) Do not use seasonal products outdoors unless marked suitable for indoor and
outdoor use. When products are used in outdoor applications, connect the
product to a Ground Fault Circuit Interrupting (GFCI) outlet. If one is not
provided, contact a qualified electrician for proper installation.
c) This seasonal use product is not intended for permanent installation or
use.
d) Do not mount or place near gas or electric heaters, fireplaces, candles or
other similar sources of heat.
e) Do not secure the wiring of the product with staples or nails, or place on
sharp hooks or nails.
f) Do not let lamps rest on the supply cord or on any wire.
g) Unplug the product when leaving the house, when retiring for the night, or
if left unattended.
h) This is an electric product-not a toy! To avoid risk of fire, burns,
personal injury and electric shock it should not be played with or placed
where small children can reach it.
i) Do not use this product for other than its intended use.
j) Do not hang ornaments or other objects from cord, wire, or light string.
k) Do not place lighting string on carpeting,drapes,furniture,or allow it to
contact vinyl siding while the power is on.
I) Do not perform any maintenance or troubleshoot for bad or broken lamps
while the power is on.
m) Do not c ose doors or windows on the product or extension cords as this may
damage the wire insulation.
n) Do not cover the product with cloth, paper or any material not part of the
product when in use.
o) This product is equipped with push-in type lamps. Do not twist lamps.
p) This product employs overload protection (fuse). A blown fuse indicates an
overload or short-circuit situation.
If the fuse blows, unplug the product from the outlet. Also unplug any
additional strings or products that may be attached to the product. Replace
the fuse as per the user servicing instructions (follow product marking for
proper fuse rating) and check the product. If the replacement fuse blows, a
short-circuit may be present and the product should be discarded.
q) Read and follow all instructions that are on the product or provided with
the product.
r) SAVE THESE INSTRUCTIONS USE AND CARE INSTRUCTIONS
a) When the product is placed on a live tree, the tree should be well
maintained and fresh. Do not place on live
trees in which the needles are brown or break off easily. Keep the tree holder
filled with waler.
b) If the product is placed on a tree, the tree should be well secured and
stable.
c) Before using or reusing, inspect product carefully. Discard any products
that have cut, damaged, or frayed wire insulation or cords, cracks in the
lampholders or enclosures, loose connections, or exposed copper wire.
d) When storing the product, carefully remove the product from wherever it is
placed, including trees, branches, or bushes, to avoid any undue strain or
stress on the product conductors, connections, and wires.
e) When not in use, store neatly in a cool, dry location protected from
sunlight.
USER SERVICING INSTRUCTIONS
Fuse replacement:
Most often, fuses blow because too many sets have been strung end-to-end.
a Before changing fuses, make sure the set is unplugged.
b Grasp plug and remove from the receptacle or other outlet device.
Do not unplug by pulling on cord.
c) Using a flathead screwdriver, o en fuse cover. Slide open
the fuse access cover on top o attachment plug towards blades.
d’ Remove fuses carefully.
e Risk of fire. Replace fuse only with 3 Amp, 125 Volt fuse (provided with
product).
f Close fuse cover. Slide closed the fuse access cover on top of attachment
plug.
Make sure door is fully closed and fuses are completely covered.
g) Risk of fire. Do not replace attachment plug. Contains a safety device
(fuse) that should not be removed. Discard product if the attachment pug is
damaged.
Bulb replacement: Before changing bulbs, make sure set is unplugged.
Step 1: Grasp plug and remove from the receptacle or other outlet device.
Do not unplug by pulling cord.
Step 2: Hold bulb b the plastic base and pull bulb/base straight out of
socket.
Step 3: Rep ace bulb with only 2.5 Volt, 0.25 Watt energy saving midget push-
in with type lamp provided product.Push spare bulb/base assembly into socket.
Donottwist bulb when inserting into socket.
If bulbs are twisted, part of the set will not light.
If the spare bulbs provided with the product have no plastic base or the
plastic base does not fit, first follow steps 1- 2 above. Then a) Remove the
old bulb by straightening the bulb wires and Puling bulb strai ht from the
base.
b) eplace the new ulb by straightening the bulb leads and aiming each wire
into a separate hole in the p astic base.
C) Make sure each bulb lead comes out an exit
opening at the bottom of the plastic base.
Now bend each lead u such that each bulb lead fits c osel against the narrow
side of the plastic base.
CAUTION:
-
This lighting string is rated 72 Watts (0.6Amps),do not overload. Connect other lighting strings or decorative outfits en -to-en up to a maximum of 216 Watts (1.8 Amps)
total. If connecting to a lighting string that does not have a Wattage (/) ratin {found on the tag within 6 inches of the plug} calculate the wattage as follows: Multiply the current(_A) whict is on the flag-type tag by 120. For example: Lighting strin is rated 120V, 60 Hz, 0.6 Amps.0.6r120- 72 Walls.
Add the wattage of each lig t string together for a total of 216 Watts or less. (Do not exceed 2’16 Watts.) -
To reduce the risk of overheating, replace burned-out lamps promptly. Use 2.5 Volt, 0.25 att lamps only.
-
To reduce the risk of fire and electric shock: a) Do not install on trees having needles, leaves or branch coverings of metal or materials which look like metal, and. b) Do not mount or support strings in a manner that can cut or damage wire insulation.
For questions and/or assistance, call customer service at
1-877-398-7337
or visit us on the web at
www.geholidaylighting.com.
02022 Nicolas Holiday Limtted ., 9F., No.37, Guangfu N Rd., Taipei, Taiwan
10560 All rights reserved.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>