Savant Technologies Dba Ge Lighting A Savant PUU-STN10-CDID Indoor Dynamic Effect Neon Rope Light
- June 4, 2024
- Savant Technologies Dba Ge Lighting A Savant
Table of Contents
Savant Technologies Dba Ge Lighting A Savant PUU-STN10-CDID Indoor
Dynamic Effect Neon Rope Light
What’s Included
Devices each sold separately
10 ft. Neon Rope Light
- 10 ft. Neon Rope Light with control box Power supply with plug
- Mounting clips
- Mounting screws
- Mounting nails
- End cap
- Alcohol Wipe
16 ft. Neon Rope Light
- 10 ft. Neon Rope Light with control box Power supply with plug .
- Mounting clips
- Mounting screws
- Mounting nails
- End cap
- Alcohol Wipe
GE is a trademark of General Electric Company, Used under trademark license.
Amazon, Alexa, and d related logos are trademarks of Amazon.com, Inc. or its
affliates. Google
and other related marks and logos are trademarks of Google LLC.
What You’ll Need
- Drill with 1/8″ drill bit (for screw installation
- Screwdriver (for screw installation)
- Hammer (for nail installation)
- Scissors
installation
Step 1-Set Up in the CYNC App
- Plug in and power on your Rope Light by pressing the On/Off button on the power supply.
- Download the Cync App, powered by Savant, on your sImartphone.
- Add your smart lights to the Cync App, then connect to Hey Google or Amazon Alexa voice assistants (sold separately) in the Cync App.
Step 2 Lay Out Your Design & Clip Placement
- Plan out your design by layout out the rope on the floor.
- Once you are happy with the design, place clips every 1t, adding extra clips at bends for reinforcement (See bending guidance)
Pro tip: take a picture of your design on the floor to reference as you install.
Rope Light Bending & Clip Reinforcement Options
Step 3 Prep the Surface & Install Your Rope Light
-
Clean and dry surface with a provided alcohol wipe. Note: Make sure the surface is dry 6& free of oil contamination. For best results, install-strip in temperatures above 50
-
F/10c. 2. Install the mounting clips on the wall based on your design needs. For complex designs, yoU may want to mark the spots on the wall where the clips will go before installing. The open end of the clip should follow the direction the ope light will go
-
Peel back the 3M tape covering and stick the clip to the wall, holding for a few seconds
-
For screw installation: Pre-drilled 1/8″ hole through the clip, then drill the screw
-
For nail installation: Hammer both trace-less nails into the clip
Clips are not strong enough to be installed with 3M tape only. They wi not be able to support the light without a screw or nails. Additionally, nails and screws wil damage walls. -
Mount the rope light into the dips by snapping the rope light into each dip. To reposition the rope light, unsnap the rope light and reinstall the mounting clip in the desired location.
Final Step-Trim to Size
If desired
-
After the strip is installed, determine if excess rope needs fo be trimmed.
-
With your Rope Light unplugged, safely cut where the trim points are indicated in black. The rope can be trimmed every 2.8
NOTE
Cutting anywhere else will permanently damage the rope.Make sure the rope light is not plugged in at the wall when cutting -
Insert the end cap on the end of the ope light.
Manually Enable Light Shows
0f applicable
- Unplug, then plug your rope light back in to detect its new length. This is inportant for Light Effects.
- Cycle through light show by pressing the Light Effects button.
Congratulations
You’ve completed the Smart Switch installation.
Next
Enable Your Voice Assistant
Connect to your Amazon Alexa or Hey Google voice assistants in the CYNC
App.
Then try this..
- Alexa, turn off the living room.
- Hey Google, turn on the lights.
- Alexa, turn on the bedroom.
- Hey Google, good morning.
- Alexa, set kitchen to 50%
- Hey Google, I’m leaving.
FCC Compliance Statement
Warning
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
Note
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communication. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
- Consult the dealer or an experienced radio/TV technician for help.
The device must not be co-located or operating in conjunction with any of her antenna or transmitter. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation
FCC RF Radiation Exposure Statement
To maintain compliance with the FCCS RF exposure guidelines, place the product at least 20cm from nearby persons.
IC Statement
This device complies with RSS247 of Industry Canada. Cet appareil se conforme à RSS247 de Canada d’lndustrie. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.
This equipment complies with IC RSS-102 radiation exposure limits set forth
for an uncontrolled environment. This transmitter must be installed to provide
a separation
distance of at least 20cm from all persons and must not be collocated or
operating in conjunction with ay other antenna or transmitter. Cet équipement
est conforme aux limites d’exposition aux rayonnements IC RSs-102 défnies pour
un environnement non contrôlé. Cet émetteur doit être installé pour fournir
une distance de séparation dau moins 20 cm de toutes les personnes et ne doit
pas être colocalisé ou fonctionner en conjonction avec une autre antenne ou
émetteur.
Like your new Indoor Dynamic Effects Neon Rope Light? Share your creations
Upload a photo or video of your space with your entertainment lights to
inspire others at gelighting.com/cync.