QING Vital Signs Monitor KY-22 User Guide
- June 6, 2024
- QING
Table of Contents
QING Vital Signs Monitor KY-22
Product description
Interface | Usage |
---|---|
W | For resetting the net-configuration |
R | For restarting the monitor |
USB power interface | For 5V power supply |
Net-configuration indicator
light
| When the indicator light is on, the monitor
enters the one-key net-configuration mode
Magnetic base| For fixing the monitor body
Monitor body| Main body of the monitor
Installation and configuration
- Confirm that there is a WIFI signal in the room, and the WIFI name and password are known;
- A mobile phone connected to the room’s WIFI network is needed;
- A tape measure or ruler is needed;
- A dry rag is needed.
Install the base
Please make a mark on the wall at the position of 1.2 meters above the bed
surface, and make sure that the mark is in the center of the bed (as shown in
the picture below);
Check the wall to make sure it is flat, dust-free and dry; then take out a
base, and tear off the adhesive protective sticker underneath; then stick the
base to the marked position(as shown in the picture), and press hard for more
than 10 seconds.
Connect power supply
Connect the data cable to the power supply port of the device and the power adapter, then turn on the power, and the device will start working.
Replace/reset network
In the power-on state, long-press the “W” hole of the monitor body with a needle. When the monitor emits a green light, it will enter the one-key network configuration mode. At this time, you can release the “W” key. Connect the mobile phone to the WIFI network in the room, scan the QR code below on We-Chat or search for the “Qinglei Technology”
official account. Follow the official account, and select the “We-Chat net- configuration” in the menu bar. Enter the WIFI network password of this room, click “Connect”. A few seconds later, it will prompt “Network configuration succeeded”. At this time, the device has successfully connected to the network. (If the network configuration is failed or time out, please retry the above steps). If there is no operation for more than 90 seconds, the device will automatically end the network configuration operation and continue to use the original network configuration.
Basic parameters
Product name: Vital Signs Monitor KY-22
Rated power : 0.75W
Rated voltage: 5V
The main body size of the monitor : φ64mm * 36mm Product net weight:
about 60g
Use environment: indoor only
Wireless connection: 802.11 b/g/n Wi-Fi @ 2.4 GHz Main material:
engineering plastics
Product color: white
FCCCaution
This device complies with part 15oftheFCCRules. Operation is subject tothe
following two conditions: (1) This device may not cause harmful
interference,and(2) this device must accept any interference
received,including interference that may cause undesired operation. AnyChanges
ormodifications notexpresslyapprovedbytheparty responsible for compliance
could void the user’sauthoritytooperate the equipment.
Note: This equipment has beentestedandfoundtocomplywiththelimits for a
class B digital device, pursuant to part15of the FCCRules. These limits are
designedto provide reasonable protectionagainstharmfulinterference in
residential installation. This equipment generates uses
andcanradiateradiofrequencyenergyand,if not installedandusedin
accordancewiththeinstructions,maycauseharmful interference
toradiocommunications. However,there isnoguaranteethatinterferencewillnot
occur inaparticularinstallation.Ifthisequipmentdoescauseharmfulinterference to
radio or television reception,whichcanbedeterminedbyturningtheequipmentoff
andon, theuseris encouraged to tryto correcttheinterferencebyoneormoreofthe
following measures:
- Reorient orrelocatethereceivingantenna.
- Increasetheseparationbetweentheequipment andreceiver.
- Connect theequipmentinto anoutletonacircuitdifferent from that towhichthe receiver is connected.
- Consult the dealer oranexperiencedradio/TVtechnicianforhelp.
This equipmentcomplieswithFCC radiation exposure limits setforthforan uncontrolled environment.