GE Lighting 93120079 Smart Dimmer Light Switch installation manual

GE Lighting 93120079 Smart Dimmer Light Switch

Specification

• OPERATION MODE: ON-OFF-ON
• CURRENT RATING: 5 Amps
• OPERATING VOLTAGE: 120 Volts
• CONTACT TYPE: Normally Closed
• CONNECTOR TYPE: Clamp
• BRAND: GE Lighting
• SWITCH STYLE: Dimmer Switch
• TERMINAL: Spst
• MATERIAL: Acrylonitrile Butadiene Styrene
• ITEM DIMENSIONS LXWXH: 21 x 7.24 x 5.71 inches
• CIRCUIT TYPE: ‎ 3-way
• MOUNTING TYPE: ‎ Wall Mount
• ACTUATOR TYPE: ‎Push Button
• CONTACT MATERIAL: ‎Plastic
• INTERNATIONAL PROTECTION RATING: ‎IP00
• UPPER-TEMPERATURE RATING: 40 Degrees Celsius
• CONTROLLER TYPE: App Control, Voice Control
• CONTROL METHOD: ‎Voice
• CONNECTIVITY PROTOCOL: ‎Wi-Fi
• COLOR: ‎ White

Introduction

Traditional light bulbs now have smart bulb capabilities thanks to the Cync Smart Switch-Dimmer, which also keeps smart bulbs smart. The smart Wi-Fi switch functions as a dimmer switch while increasing the capabilities of the conventional bulb to include scene setting, scheduling, and control from outside the house. The smart switch, when used with C by GE Smart Bulbs, enables app or voice control even when the power is off at the switch. Control all of the lights in the space from a single wall switch by combining the Smart Switch with C by GE Smart Bulbs in other fixtures, such as table lamps.

The C by GE Smart Switch wirelessly connects to other C by GE Smart Switches, allowing you to control the same light fixture from several switches, even if they are on separate circuits. Easy DIY setup. Without the need for a hub, the Smart Switch can connect directly to Google Home and Amazon Alexa gadgets. No neutral wire is necessary; works with the majority of residential wiring types.

WARNING: RISK OF ELECTRIC SHOCK

This product installation requires handling 120-volt wiring. Follow each step carefully.

If you have any concerns handling wiring, hire a qualified electrician. Ensure all work meets local and federal regulations.

WARNING – This control must be installed with an external isolating wall control/switch in series with the ungrounded conductor, providing an air gap as per National Electrical Code (NEC) ANSI/NFPA 70 article 404, and Canadian Electric Code, Part 1 (CEC)

SIMPLE DIY SETUP

STEP 1: Install your Smart Switch

STEP 2: Download the Cync App, powered by Savant, on your smartphone

STEP 3: Add your Smart Switch to the Cync App

COMPATIBILITY REQUIREMENTS

• Rating 120V AC 60Hz
• Neutral wire is not required. (Wire is usually white or grey and is not required)
• Ground wire is required. (Wire is usually green, green with a yellow stripe, or copper)
• Wi-Fi 802.11 b/g/n @ 2.4 GHZ is required.
• Works with halogen, incandescent, and LED bulbs, including C by GE and Cync Smart Bulbs
• Not for use with ceiling fans.
• LED up to 1.25 amps (150 Watts)
• Incandescent/halogen up to 5 amps (450 Watts)
• Minimum Load 15 Watts
• If you are using less than 15 Watts, non-dimmable LED bulbs, or C by GE or Cync Smart Bulbs on the circuit, you will need to use the included Bulb Adaptor
• Use the optional Fixture Adaptor (available separately) where the Bulb Adaptor will not fit. Contact Customer Support at 1-844-302-2943 for details.

IMPORTANT NOTE ON 3-WAY WIRING:

Some lights have one wall switch, while others are controlled by two or more wall switches (such as stair lights, which have a switch at both the top and bottom of the stairs). If your lights have more than one switch (called a 3-way), we’ve created other instructions for this type of installation.

INCLUDED

YOU’LL NEED

BEFORE YOU DO ANYTHING!

Turn Off the Power!

STEP 1: Turn off the power for the switch location at the circuit breaker box.

STEP 2: Test existing switch by toggling switch on/off, ensuring lights do not turn on.

STEP 3: Now, follow these setup steps for a single gang switch.

WHAT TYPE OF BULBS DO YOU PLAN TO USE? YOU MAY NEED TO INSTALL A BULB ADAPTOR.

Some installations require the included Bulb Adaptor to maintain Wi-Fi connectivity and to ensure your switch and bulbs work together.

If your switch circuit includes a load of at least 15 Watts:

If your switch circuit does NOT include a load of at least 15 Watts:

STEP 1: Twist the Bulb Adaptor onto the base of the medium-base (E26) light bulb.

STEP 2: Screw the bulb and Adaptor into the fixture.

NOTE: Only one Bulb Adaptor is needed per switch, even if there are multiple light bulbs on the circuit. If installing in a recessed can application, you may need to adjust the recessed can depth to ensure the bulb is flush.

If the Bulb Adaptor does not fit your bulb or fixture, you have other options:

• Replace your lights with incandescent, halogen, or dimmable LED light bulbs that meet the 15-Watt minimum load requirement. See a list of compatible bulbs at gelighting.com/cync
• Install our Fixture Adaptor to the actual fixture in the ceiling. For install instructions and where to get a C by GE or Cync Fixture Adaptor (available separately), contact Customer Support at 1-844-302-2943

REMOVE YOUR OLD SWITCH

• STEP 1: Remove the existing wall plate and switch from the wall.
• STEP 2: Use voltage tester on the black wires to confirm power to the switch is off (recommended).
• STEP 3: Before disconnecting the wires from the wall, label each with the provided wire labels. Ground wire is required. If you don’t have this wire, the Cync or C by GE Smart Switch is not compatible.
• STEP 4: Disconnect wires and remove existing switch.

CONNECT THE WIRES

NOTE: Both black wires on the switch are interchangeable and can be connected to either the load or line wire from the wall.

STEP 1: Connect the first line/load (black) wire on the switch to the line or load (black label) wire from the wall.

STEP 2: Connect the second line/load (black) wire on the switch to the line or load (black label) wire from the wall.

STEP 3: Connect the ground (green) wire on the switch with the ground (green label) wire from the wall.

STEP 4: Cap the 3-way/multi-way traveler wire (if applicable). For 3-way switch setup, visit gelighting.com/cync.

ATTENTION: Incorrectly connecting the ground wire from the wall to the ground wire on the switch will damage the product.

STEP 5: Cap the neutral wire from the wall (if applicable). Neutral wire is not required to operate this switch.

USING WIRE NUTS

1. Insert wires into wire nut.
2. Turn wire nut clockwise.
3. Pull gently on wires to test connection.

FIT WIRES INTO WALL BOX

STEP 1

Neatly push the wires back into the box, rotating the switch so it’s oriented according to the image, and the arrow on the switch is pointing up.

SECURE THE SMART SWITCH

STEP 1

Using a Phillips screwdriver and the screws provided, secure the switch to the wall until level and flush. Then snap the faceplate cover onto the bracket.

• If using your existing wall plate, you may need to replace the existing wall plate screws with the short screws provided.

TURN THE POWER BACK ON

TIP: To enable the full experience, you’ll need to set up all your products in the Cync App. If you’ve set up C by GE or Cync bulbs in the Google Home app, visit gelighting.com/cync for unpairing instructions.

STEP 1: After the switch is secured and the faceplate is mounted, turn the power back on at the circuit breaker box.

STEP 2: The light ring will flash blue indicating the device is wired correctly and the device is in setup mode. Press any button on the switch to enable setup mode if setup mode times out.

TROUBLESHOOTING

• LED indicator light or light ring will flash blue until the switch is added to the Cync App.
• LED indicator light or light ring will not illuminate if wired incorrectly or if the switch circuit does not meet the specified load requirements.

IF LIGHTS DON’T TURN ON:

STEP 1: Check that power to the switch is on at the breaker.

STEP 2: Turn power off at the breaker, return to the switch to confirm the wires are securely and properly wired according to the installation guide.

STEP 3: Go to gelighting.com/cync for more troubleshooting.

IF LIGHTS FLICKER, EXPERIENCE INTERMITTENT POWER LOSS, OR WON’T COMPLETELY TURN OFF:

STEP 1: Be sure to select the correct bulb type in the Cync App.

STEP 2: Your installation may require a Bulb/Fixture Adaptor or a different bulb type. See pages 9-10 for more details or visit gelighting.com/cync for troubleshooting help.

SIMPLE SET UP USING THE CYNC APP

Unlock full features and connect to other CYNC devices

STEP 1: Install your Smart Switch

STEP 2: Download the Cync App, powered by Savant, on your smartphone

STEP 3: Add your Smart Switch to the Cync App

STEP 4: Easily connect your Smart Switch to your Amazon Alexa- or Hey Google-enabled device in the Cync App. Click settings in the Cync App. Then click the voice assistant you’d like to enable and follow the in-app setup instructions.

AMAZON ALEXA

To set up, open the Alexa app, search for the Cync skill, follow the setup instructions.

TRY THIS…

• Alexa, turn off the living room.
• Alexa, turn on the bedroom.

HEY GOOGLE

To set up, open the Hey Google or Google Home app, search for the Cync action, follow the setup instructions.

TRY THIS…

• Hey Google, turn on the lights.
• Hey Google, good morning.
• Hey Google, I’m leaving.

FAQs

I have a ceiling fan, can this work with that as well? It has bulbs too.****

If your ceiling fan and the lights attached to the ceiling fan are controlled by the same switch, this will not work as intended.

Are these compatible with Smartthings (Zwave, WIFI, or Zigbee)?****

C by GE Smart Switches will work through WIFI but will need to be connected to our C by GE app first. The Smart Switches will not work with Smartthings.

Is there a way to change the settings so that the lights come on in a “slow fade” rather than just turning on quickly when there is motion detected?****

There are three settings for this switch and none of which provide you with a slow fade setting.

Can one of these be use as a 2-switch system. I have one switch that act as 2 switches for the living room and another one for the kitchen.****

If your intent is to use these switches as a 3-way (2 switches controlling 1 set of lights) then yes, our switches can do that. However, both switches will need to be C by GE switches. Please contact our support staff for more information regarding the switches, thank you!

Ge cync smart dimmer light switch is how deep?****

The entire unit’s dimensions are 105 x 44.5 x 41 mm. The dimensions of the back housing of the switch is 60 x 44.5 x 30 mm. We would be more than happy to answer additional questions and concerns directly.

Wi-Fi is 2/3 bars on my phone next to the switch, but the switch will fail to connect; do I have a bad switch?****

We apologize your switch has not been able to connect. All Cync devices are rated to operate on 2.4GHz as opposed to a 5GHz, please ensure you are connected to 2.4GHz. Should you need further assistance please contact us directly.

Will this switch work with a fan/light? The fan/light has its own switch for each and the wall switch controls the power.****

Yes. I have both a fan/light combo controlled and separate fan & light controlled. You may find that some bulbs flicker with this switch. The switch comes with an adapter to fix this on some bulbs but I found a few still flicker even with the adapter. But it’s easy enough to buy a different bulb for the light part that doesn’t flicker. Most of the LED ones I tried flickered but CFL did not.

I have a 3-gang light switch. Are these compatible with standard wall plates?****

Yes, our 4-Wire Dimmer Switch does fit in most standard wall plates. Should you have any further questions please feel free to reach out to us directly.

Does it support any dimmable leds? I have bbounder leds from amazon which work fine with WeMo but not dimming with this one.****

We have a list of known compatible bulbs that have been tested with these switches you can find that information at https://www.gelighting.com/compatibility. We also sell our own dimmable LED bulbs that work with these switches, you will just have to set the bulb type in the switch settings. Please reach out to our support team if you need further assistance.

Will these get thread and homekit support? it was announced that cync would support homekit soon****

We have a few products that work with homekit and we are looking to expand that. I will be sure to forward this info to our development team for future support with homekit with our other products.

Is it possible to dim it below 5%?****

Unfortunately, these switches only dim in increments of 5%. If you have any further questions you can also contact us directly.

Will this control the ge cync light strip?****

Our Wire Free Smart Switch is able to control the Cync Smart LED Light Strip. Should you have any further questions please feel free to reach out to us directly.

I have a 400-watt pool light that I want to pair this with. Outlet has 3 wire, no neutral. Will this switch work outside with google?****

Unfortunately, our switches are not rated for outdoor use. We do not recommend them to be used in outdoor situations.

Can Alexa dim the lights?****

Yes, Alexa will be able to dim the 3-wire dimmer switch on voice command.

Is it compatible with Nest App?****

our switches need to be setup in the C by GE app first and then can be linked to either the Google Home app or the Alexa app. If you have any more questions please give us a call at 844-302-2943.

Video

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>